background image

MT318-101 

User’s Guide

 

400-0742-001 

 

 
 
 
 
 
 

 

8. 

[HWEN] 

This command enables or disables the card hardware, 
excluding the main microprocessor. Power to video and 
audio circuitry is turned off. Use for saving power but to 
keep response time short returning to normal operation. 

Either HDBT receiver can be disabled individually or as a 
pair. This is not a group command. 

Show the status of the hardware enable. 

Command Format:  [HWENCii] 

Returns [x] 

= 0 

Rx1 and Rx2 are off 

 

= 1 

Rx1 and Rx2 are on 

 

= 2 

Rx1 on, Rx2 off 

 

= 3 

Rx1 off, Rx2 on 

Command Format:  [HWENxCii] 

= On/off  (1 = on, 0 = off) 

Command Format:  [HWENxnCii] 

= On/off  (1 = on, 0 = off) 

= HDBT Rx  (1 or 2) 

Example: 

Disable the hardware to the HDBT Rx card in slot 4 by 
sending the following command: 

[HWEN0C4] 

9. 

[MOD] 

This command returns the card model number. 

Command Format:  [MODCii] 

Example: 

Read the model of the card in slot 4 by sending [MODC4]; 
feedback is like the following: 

[MT318-101C04] 

10.  [PRG] 

This command puts the card into firmware update mode. 
Only use when working with Altinex Technical Support. 

Command Format:  [PRGCii] 

11.  [PWR] 

This command returns the card power consumption in 
watts. 

Command Format:  [PWRCii] 

Example: 

Read the power consumption of the card in slot 4 by 
sending [PWRC4]; feedback is like the following: 

[4.59WC04] 

12.  [PWRM] 

Same as the [PWR] command but returns milliwatts. 

Command Format:  [PWRMCii] 

Example: 

Read the power consumption (in milliwatts) of the card in 
slot 4 by sending [PWRMC4]; feedback is like the following: 

[4596mWC04] 

13.  [SFT] 

This command resets the card. It is the equivalent to 
powering just the card off and on. 

Command Format:  [SFTCii] 

Example: 

Reset the card in slot by sending [SFTC4]. The card 
responds with [RSTC04] indicating the card is resetting. 

14.  [STA] 

This command enables and disables automatic feedback 
from the card. The feedback format is the same as the [?Ci] 
command, but only changes are reported.  

Command Format:  [STAxCii] 

= On/off (x = 1 to enable, 0 disables) 

Feedback Prefix Definitions: 

MT  Card Model Number 
RI 

RS232 Settings 

VR  Firmware Revision 
PR  Card power consumption 
TP  Card Temperature 

15.  [TEMP] 

Read card temperature in degrees Celsius. 

Command Format:  [TEMPCii] 

Example: 

Send [TEMPC4] to read the temperature of slot 4

’s card. 

[39C04] 

16.  [VER] 

This command displays the software version and card type 
for the card. 

Command Format: [VERCii] 

Example: 

Send the command [VERC4] to check the version of the 
MT318-101 in slot 4.  The card returns feedback: 

[690-0465-001C04] 

690-0465-001 = firmware version 
C04  = card ID 

 

Содержание MT318-101








Отзывы: