background image

D-000348 Rev. A 

Indications for Contraindication for Use  

 
Statement of Intended Use 
The AlterG Via400 Anti-Gravity Treadmill provide unweighting of the user’s body weight 
in addition to normal treadmill functions. The unweighting allows patients and individuals 
to do standing exercises, walk, or run with reduced impact on their musculoskeletal 
system. 

 

 
Indications for Use 
 

Aerobic conditioning Sport specific conditioning programs 
Weight control and reduction 
Gait training and neuromuscular re-education in neurologic patients 
Strengthening and conditioning in geriatric patients 
Rehabilitation following injury or surgery of the lower extremity 
Rehabilitation after total joint replacement 

 

Precautions for Use 

 

Cardiovascular disease or respiratory compromise 
Exercise induced asthma or angina 
Acute and chronic back problems 
Ruptured or herniated disc 
Safety and effectiveness in pregnant women has not been established 
Safety and effectiveness for individuals with Functional Independence Measure 

score of 1 or 2 (dependent of max assist) has not been established 

Treadmill belt does not lock in place. Be sure patient is stable before turning off the 

treadmill and exiting 

Heart rate monitor is not accurate 

Any condition where increased intra-abdominal pressure may be a concern (for 

example urinary incontinence, pelvic floor dysfunction, pelvic floor 
reconstruction, or other conditions)

 

 
Contraindications for Use 

 

Unstable fracture 
Cardiovascular hypotension 
Deep vein thrombosis 

 

“This appliance is not intended for use by persons with reduced physical, sensory or 
mental capabilities, or lack of experience and knowledge, unless they have been given 
supervision or instruction concerning use of the appliance by a person responsible for 
their safety. Keep children under the age of 13 away from this machine.” 

Содержание Anti-Gravity Treadmill Via 400

























































Отзывы: