Alpine X009E, Руководство пользователя

Страница: 46 / 212

46
-EN
01GB05X009E.fm
ALPINE X009E 68-24567Z66-A (EN)
Adjusting the Crossover Settings
(X-OVER)
[X-OVER] is selected on the Sound setup menu in step 3. Refer to
“Sound Setup Operation” (page 43).
Before performing the following procedures, refer to “About the
Crossover” (page 48).
Setting item: X-OVER
1
Touch
[Channel]
to select the channel.
Each time you touch, the channel switches.
• The channel being adjusted is displayed in red.
2
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch
[ ]
or
[ ]
of “Freq.”, and then select the cut-off
frequency.
Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) /
100 / 125 / 160 / 200 Hz
Adjusting the Slope
Touch [ ] or [ ] of “Slope”, and then adjust the HPF or LPF
slope.
Setting contents: 0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct.
Adjusting the Level
Touch
[ ]
or
[ ]
of “Level”, and then adjust the HPF or LPF
level.
Setting contents: -12 to 0 dB (Initial setting: 0)
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
4
To store the adjusted setting value, touch and hold
[Preset1]
,
[Preset2]
, or
[Preset3]
for at least 2
seconds.
• Touch [Flat] to initialize all values.
• If the Rear Speaker setting is “Off”, the Rear Speaker setting cannot
be edited (refer to page 43).
• If the Subwoofer setting is “Off”, the Subwoofer setting cannot be
edited (refer to page 43).
• While adjusting the X-OVER you should consider the frequency
response of the connected speakers.
Calling the X-OVER adjusted value
Calling the pre-set X-OVER adjusted value.
Touch
[Preset1]
,
[Preset2]
, or
[Preset3]
on the
X-OVER screen.
The setting stored in the Preset will be recalled.
Setting Defeat
[Defeat] is selected on the Sound setup menu in step 3. Refer to “Sound
Setup Operation” (page 43).
If Defeat is “On”, MX, Equalizer Presets, Car Specific Sound Setup and
Parametric EQ functions are turned OFF. This disables any settings
made for these functions.
Setting item: Defeat
Setting contents: Off (Initial setting) / On
Volume Setting
[Volume] is selected on the Sound setup menu in step 3. Refer to
“Sound Setup Operation” (page 43).
You can change the volume of the sound heard when a button is
touched.
Setting item: Key Sound Feedback
Setting contents: 0 to 7 (Initial setting: 4)
Setting the Volume for Each Source
[Source Volume Setup] is selected on the Sound setup menu in step 3.
Refer to “Sound Setup Operation” (page 43).
The volume level for each application can be adjusted.
Setting item: Radio / DVD / CD / Compressed Media /
iPod Music / iPod Video / HDMI / AUX / AUX3 /
BLUETOOTH Audio
Setting contents: -14 to +14 (Initial setting: 0)
• Settable source differ depending on the connected device and
settings.
About Time Correction
The distance between the listener and the speakers in a car vary widely
due to the complex speaker placement. This difference in the distances
from the speakers to the listener creates a shift in the sounds image and
frequency characteristics. This is caused by the time delay between the
sound reaching the listener’s right versus the left ear.
To correct this, this unit is able to delay the audio signal to the speakers
closest to the listener. This effectively creates a perception of increased
distance for those speakers. The listener can be placed at an equal
distance between the left and right speakers for optimum staging.
The adjustment will be made for each speaker in 3.4 cm steps.
Front HPF Rear HPF Subw. LPF
01GB00X009E.book Page 46 Friday, May 9, 2014 1:16 PM