Alpha ARES Pro 150 Скачать руководство пользователя страница 37

Страница: 37 / 44

Inspections and maintenance

4.2 ADAPT IT FOR USE WITH

OTHER GASES

e boilers are produced for the type of gas spe

cific

ally requested when

placing the order.

DANGER !

Transformation of the boiler to operate with a dif-

ferent type of gas than the one spe

cifi

cally requested

when ordering must be carried out by professionally

qua

lifi

ed sta

in compliance with the regulations

in force.

e manufacturer shall not be held liable for any

damage deriving from incorrect transformation op-

erations or which were not carried out in compliance

with current regulations and/or instructions given.

ATTENTION !

er transforming the boiler for operation with

diff

erent type of gas (for example, propane gas)

than the one spe

cifi

cally requested when placing the

order, the appliance can only operate with the said

new type of gas.

ATTENTION !

Instructions for appliances running on propane gas

Make sure that the gas tank has been deaerated prior

to installing the appliance.

For a thorough deaeration of the tank contact the

liquid gas supplier and in any case authorised sta

in accordance with the law.

Ignition problems can arise if the tank is not thor-

oughly deaerated.

In this case contact the liquid gas tank supplier.

•

GAS TRANSFORMATION

Adjust the Min / Max GAS pressure switches

only for models: ARES PRO 230 - 300 - 348 - 400 - 500 - 600.

Methane Gas = 10 mbar

Methane Gas/LPG = 50 mbar

LPG = 15 mbar

Edit the parameters

FH and FL fan max and min revs.

(*) for the values, refer to the NOZZLES - PRESSURES - FLOW RATES TABLE

Code

Symb.

Description

Value

526

Fan:

Maximum revs

(*)

346

Fan:

Minimum revs

(*)

- Follow the instructions for Burner Adjustment (Chap. regarding

METH

ANE/LPG fl

ue adjusting device).

- Once the transformation is completed,

ll in the information

provided on the label supplied in the documentation envelope and

ffix i

t to the side of the boiler’s technical data label.

•

EXAMPLE OF COMPILATION

Содержание ARES Pro 150













































Результаты поиска

Содержание ARES Pro 150

Отзывы:

Похожие инструкции для ARES Pro 150

Бренды по названию

Популярные бренды

Alpha ARES Pro 150, Инструкции по установке и обслуживанию

Результаты поиска

Содержание ARES Pro 150

Отзывы:

Похожие инструкции для ARES Pro 150

Бренды по названию

Популярные бренды