Alpha Alpha CD18S Скачать руководство пользователя

Страница: 35 / 36

Alpha CD18S/24S/30S - Service History

CHECKLIST

Ensure the following is completed after the boiler has been installed and commissioned:-

BOILER SERIAL No. ......................................................... NOTIFICATION No. ..........................................................

CONTROLS

To comply with the Building Regulations, each section must have a tick in one or other of the boxes

Time & temperature control to heating

Time & temperature control to hot water

Heating zone valves

Hot water zone valves

Thermostatic radiator valves

Automatic by-pass to system

FOR ALL BOILERS CONFIRM THE FOLLOWING:

The system has been flushed in accordance with the boiler manufacturer's instructions?

Yes

The system cleaner used ....................................................................................................................

The inhibitor used ................................................................................................................................

FOR CENTRAL HEATING MODE, MEASURE AND RECORD THE FOLLOWING:

Gas rate

m³/hr

ft³/hr

Burner operating pressure (if applicable)

N/A

mbar

Central heating flow temperature

°C

Central heating return temperature

°C

FOR COMBINATION BOILERS ONLY

Has a water scale reducer been fitted?

Yes

What type of scale reducer has been fitted? ......................................................................................

FOR DOMESTIC HOT WATER MODE, MEASURE AND RECORD THE FOLLOWING:

Gas rate

m³/hr

ft³/hr

Maximum burner operating pressure (if applicable)

N/A

mbar

Cold water inlet temperature

°C

Hot water outlet temperature

°C

Water flow rate

lts/min

FOR CONDENSING BOILERS ONLY CONFIRM THE FOLLOWING:

The condensate drain has been installed in accordance with the manufacturer's instructions?

Yes

FOR ALL INSTALLATIONS CONFIRM THE FOLLOWING:

The heating and hot water system complies with current Building Regulations

Yes

The appliance and associated equipment has been installed and commissioned
in accordance with the manufacturer's instructions

Yes

If required by the manufacturer, have you recorded a CO/CO

ratio reading

N/A

Yes

CO/CO

ratio

The operation of the appliance and system controls have been demonstrated to the customer

Yes

The manufacturer's literature has been left with the customer

Yes

COMMISSIONING ENG'S NAME:

Print ...................................................................... CORGI ID No. ..................................................

Sign ...................................................................... Date .................................................................

room t/stat & programmer/timer

cylinder t/stat & programmer/timer

Fitted

Programmable roomstat

Combi boiler

Not required

Содержание Alpha CD18S





































Результаты поиска

Содержание Alpha CD18S

Отзывы:

Похожие инструкции для Alpha CD18S

Бренды по названию

Популярные бренды

Alpha Alpha CD18S, Инструкции по установке и обслуживанию

Результаты поиска

Содержание Alpha CD18S

Отзывы:

Похожие инструкции для Alpha CD18S

Бренды по названию

Популярные бренды