Alpego SKAT K1 5-250 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 24

Alpego SKAT K1 5-250 Скачать руководство пользователя страница 14

MANUALE SKAT K1 - K2

Old Cod.D08974

New Cod. MANT2010/00722 R.9

INSTALLATION

- 10

Copyright ©2009 della Alpego spa® - All rights are reserved. Reprinting or unauthorized use of this manual is strictly forbidden without written permission by Alpego spa

4.5. CHECKING THE TRACTOR LIFTING FORCE AND STABILITY

When an extra machine is added to the tractor, becoming a part of the tractor itself, as far as road circulation
is concerned, stability is different and driving and working become more difficult.

Depending on the composition of the machine, it is therefore advisable to add ballast to the front part of the tractor so
as to adequately distribute the weight on the axles.

A

Distance of the f ront axle f rom the f ront ballast (m) 1

1

B

Tractor wheelbase (m)

2

C

Distance of the rear axle f rom the implement’s lower hitch (m)

2

Gv

Ballast weight (kg)

3

Te

Empty weight of the tractor

2

Tv

Load on the tractor’s f ront axle when empty

2

Th

Load on the tractor’s rear axle when empty

2

Lb tot

Distance f rom the lower hitch to the center of grav ity of the complete implement combination (m)

3

Lb1

Distance f rom the lower hitch to the center of grav ity of the f irst combi machine (m)

1

Lb2

Distance f rom the lower hitch to the center of grav ity of the second combi machine (m)

1

Mb1

Ov erall weight of the f irst implement (kg)

4

Mb2

Ov erall weight of the second implement (kg)

4

Mb tot

Ov erall weight of the complete implement combination (kg)

3

1) Must be measured.
2) Consult the tractor’s operation and maintenance manual.
3) Must be calculated.
4) Consult the operation and maintenance manual of the required implement.

«
...
12
13
14
15
16
...
»

Содержание SKAT K1 5-250

























Отзывы:

Нет отзывов