Alpego SKAT K1 5-250 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

Alpego SKAT K1 5-250 Скачать руководство пользователя страница 12

MANUALE SKAT K1 - K2

Old Cod.D08974

New Cod. MANT2010/00722 R.9

INSTALLATION

- 8

Copyright ©2009 della Alpego spa® - All rights are reserved. Reprinting or unauthorized use of this manual is strictly forbidden without written permission by Alpego spa

2) Insert shaft D onto support C then assemble the articulation bolt A without

tightening it; just position the screw head and the bolt against the shank
support sheet. Rotate the shank and assemble safety bolt B, then tighten
all the bolts

.

3) Lower the rear supporting leg into its position and lock it using the pins.

Insert safety pins B into the 2 front side shank supports.
When the hydraulic system of the machine has been loaded and/or while working, move pins to position A

CENTRAL HOLE
POS.

K1-K2

4) When the previous phases have been carried out the subsoiler can be positioned on a horizontal surface with the

supporting legs and shanks lowered.

Make sure that the pins are in position A.

When moving the subsoiler use the
hooking points indicated on the sticker
(see section 4.1).

As this operation could be dangerous, maximum
caution is expected.  Keep unauthorised people away
from the area and check suitability of the available
means.  Do not touch hanging loads and keep safety
distance.

«
...
10
11
12
13
14
...
»

Содержание SKAT K1 5-250

























Отзывы:

Нет отзывов