background image

24

Distributed by: AFW Access Systems
www.AnchorMiami.com (305)691-7711

This Gate Operator is built in the USA and 
complies with all requirements of 
Underwriters' Laboratories Standard UL-325.   
P/N 110136              Rev. F       December  2003

PHYSICAL 

PAD:

18-1/4” W x 18-1/4”D x 3”H Elevation 

OVERHEAD CLEARANCE: 

Minimum 25” Required 

UNIT SIZE: 

15”W x 19”D x 24-1/4” H 

FRAME: 

Welded, Uni-Body; Phosphatized And 

COVER: 

Architecturally Designed, Rust Free 
LLPE; Key Lock To Prevent 

SHIPPING WEIGHT: 

115 lbs. 

PRIMARY VOLTAGE: 

115 VAC, 60 Hz, Single Phase 

ELECTRICAL SOURCE: 

One 3-Wire, 15-Amp Service From 

CONTROL VOLTAGE: 

5 VDC 

RADIO RECEIVER POWER: 

24 VAC, 20 mA 

MOTOR: 

1/2 HP, 4.4 Amp, PSC, Instant 
Reversing, Thermally Protected (Manual 

AUTO TIMER-TO-CLOSE: 

Built-In, Adjustable From 2-60 Seconds 

ELECTRICAL 

DRIVE 

DRIVE SYSTEM: 

Gearbox; 10:1; With Bronze Worm & 
Pinion Gears 

TOTAL SPEED REDUCTION: 

22.2:1 

OUTPUT SHAFT: 

1” dia., Ball-Bearing Mounted 

DRIVE MECHANISM: 

18-Tooth Sprocket; #41 Roller Chain 

LIMITS: 

Independent Open & Close; Displaced 
Cam With Micro-Switch Contacts; 
Adjustable Without Tools 

OPERATOR LOCK: 

Electro-Mechanical, AC Solenoid; 
Engages On Close Limit, Drops Out If 
Power Is Interrupted 

MAX. GATE WEIGHT: 

1,100 lbs., Level Grade 

MAX. GATE WIDTH: 

29 ft. 

MAX. CYCLES PER HOUR: 

45 Open/Close Per Hour; 800 Open/
Close Per Day (All Calculations Based 
On Typical 20’ Gate On Level Grade) 

GATE SPEED: 

11.8 inches/second 

CAPACITIES 

Specifications subject to change without notice.  Consult the factory. 

Manufacturer’s Limited Warranty

Allstar warrants its gate operators to be free from defect in material and workmanship for a period of five (5) years from the date of purchase 
for single family home use and three (3) years from the date of purchase for multi-family and commercial use.  This warranty covers all 
components except the electronic circuit boards which are warranted for three (3) years from the date of purchase for single family home use 
and two (2) years from the date of purchase for multi-family and commercial use.  To obtain service contact your dealer.  

To obtain service under this warranty the buyer must obtain authorization instructions for the return of any goods from Allstar before 
returning the goods.  The goods must be returned with complete identification, with copy of proof-of-purchase, freight prepaid and in 
accordance with Allstar’s instructions or they will not be accepted.  In no event will Allstar be responsible for goods returned without proper 
authorization or identification. 

Goods returned to Allstar for warranty repair within the warranty period, which upon receipt by Allstar are confirmed to be defective and 
covered by this limited warranty, will be repaired or replaced at Allstar’s sole option, at no cost and returned pre-paid.  Defective parts will 
be repaired or replaced with new or factory rebuilt parts at Allstar’s sole option. 

This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage caused by improper installation or 
care, vandalism or lightning, fire or excessive heat, flood or other acts of God (including, but not limited to misuse, abuse or alterations, 
failure to provide reasonable and necessary maintenance), labor charges for dismantling or reinstalling a repaired or replaced unit, or 
replacement batteries. 

These warranties are in lieu of all other warranties, either expressed or implied.  All implied warranties of merchantability and/or fitness for a 
particular purpose are hereby disclaimed and excluded.  Under no circumstances shall Allstar be liable for consequential, incidental or 
special damages arising in connection with the use or inability to use this product.  In no event shall Allstar’s liability for breach of warranty, 
breach of contract, negligence or strict liability exceed the cost of the product covered hereby.  No person is authorized to assume for Allstar 
any other liability in connection with the sale of this product. 

This warranty gives you specific legal rights.  You may also have other rights which vary from state to state.  Warranty effective after June 1, 
2000. 

  TECHNICAL SPECIFICATIONS  

Содержание LEADER PLUS LP1000

























Отзывы: