Allied Skid-Pac 1000 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 44

Allied Skid-Pac 1000 Скачать руководство пользователя страница 26

Allied Construction Products, LLC www.alliedcp.com

TM103349_SP1000B_15sep

16

9.0 Care & Maintenance - [cont’d]

6. Repeat steps 1-4 with other bearing and housing.

7. Install the bearings and eccentric in to the

eccentric housing. Install bolts.

8. Install hydraulic motor and bolts.

9. Install hydraulic hoses.

IMPORTANT

Keep threaded fasteners tight. Replace with new if
missing or damaged. Replacement fasteners must
be the same type and grade. Follow proper
tightening procedures and bolt torque.

9.7 Rubber Springs - Replacement

The rubber springs will require periodic replacement
due to aging. Other factors that adversely affect the
longevity of the rubber include abrasions, over-
stretching and prolonged operating cycles that build-
up heat in the rubber. Stopping the Skid-Pac during
repositioning can help minimize heat-aging.

CAUTION

Crush injury. Do not place hands or
fingers between mounting frame and
compaction plate during removal of
spring mounts.

Ensure all loads are adequately supported before
performing any service work.

CAUTION

Some components of the Skid-Pac are heavy. Use
approved lifting equipment to properly support and
stabilize loads.

NOTE: If multiple mounts are to be replaced, it is
recommended to replace one mount at a time.

1. Position Skid-Pac on flat, stable surface.

2. Support top mounting frame to remove weight

from mounts.

3.  Loosen all nuts. Remove nuts and washers.

4.  Remove all bolts and mount.

5.  Position new mount. Use alignment bar to align

bolt holes.

6. Install new bolts, washers and nuts.

7. Tighten bolt to proper torque. Refer to Table 9.2.

Fig. 9-4 Flat Washer (3) must be placed against

‘rubber side’ (1) of Spring Mount

IMPORTANT

Flat washer must be installed on the “Rubber Side”
of mount. Refer to Figure 9-3.

9.8 Threaded Fasteners

IMPORTANT

All threaded fasteners must be checked frequently
for loose, broken or missing bolts. Keep threaded
fasteners tight. Replace with new if missing or
damaged. Replacement fasteners must be the same
type and grade. Follow proper tightening procedures
and bolt torque.

9.8.1 Bolts – Replacement, Preparation,
Tightening Method, Pre-tensioning and Torque



Replacement fasteners must be the same type
and grade.



A hardened washer must be used under the head
of a bolt in a blind hole.



With a nut and bolt combination, a hardened
washer must be used under the element to be
turned. AND the element not turned must be
prevented from rotating during tightening.



Do not apply thread lock compound to the bolt
threads unless instructed to do so.



All threads must be free of damage and foreign
debris. Surfaces to be bolted must be flat.



The threads of bolt should be lightly lubricated.



Install all bolts finger tight.

«
...
24
25
26
27
28
...
»

Содержание Skid-Pac 1000













































Отзывы:

Нет отзывов