Allied Skid-Pac 1000 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 44

Allied Skid-Pac 1000 Скачать руководство пользователя страница 24

Allied Construction Products, LLC www.alliedcp.com

TM103349_SP1000B_15sep

14

9.0 Care & Maintenance - [cont’d]

Bearing Lubrication – Type (1000)

The Allied Skid-Pac is factory filled with premium
quality hydraulic oil ISO VG32 combining non-foam
and anti-wear additives. The use of other oils shall
be permitted only if they have a minimum viscosity of
at least 12 cSt at an operating temperature of 66



C

(150



F).

Oil Capacity (1000)

Approximate oil capacity is 2.4 qt (2.2 l).

Do not overfill.

Excess oil (from over-filling) will

discharge through the pressure relief plug.

Oil Change Interval (1000)

Replace the bearing oil every 1000 operating hours,
or once per year. *Maintenance intervals are subject
to adjustment if operating under extreme operating
conditions.

9.5.3 Pressure Relief Valve (1000)

The pressure relief valve, located on the eccentric
housing near the fill plug, vents any pressure build-up
inside the eccentric housing. A slight accumulation of
oil residue surrounding its location is normal.

9.5.4 How To Check Oil Level (1000)

CAUTION

Hot surface - Burn injury if contacted.
Some components of the machinery
become hot during operation. Allow parts
and fluids to cool before handling.

IMPORTANT

Contamination can shorten bearing life. Prevent dirt
and debris from contaminating the oil. Always clean
the area around the plugs prior to removal.

Oil Fill

Oil Level

Fig. 9-1 Oil Fill and Level Labels Identified

Fig. 9-2 Oil Level & Fill Locations Identified (1000)

1. Position the Skid-Pac on a level surface with

easy access to both the oil fill and oil level plugs.

2. Prevent contamination by cleaning area around

the oil level plug before removal.

3. With plug removed, the oil level should be visible

at the bottom of the opening.

1-Eccentric Housing

2-Oil Level Decal

3-Oil Level Plug

4-Oil Level Max.

Fig. 9-3 Oil Level for Bearings (1000)

9.5.5 How To Add Oil (1000)

1. Position the Skid-Pac on a level surface with

easy access to both the oil fill and oil level plugs.
Refer to Figure 9-2.

2. Clean the area around the oil fill plug before

removing.

3.  Add oil until excess drips from the opening.

4.  Install and tighten oil fill and level plugs.

5.  Wipe up any oil spills

2

3

4

«
...
22
23
24
25
26
...
»

Содержание Skid-Pac 1000













































Отзывы:

Нет отзывов