Allied HO-PAC 4000 Скачать руководство пользователя

Страница: 5 / 44

Allied Construction Products, LLC www.alliedcp.com

TM574173_HP4000_18feb

SAFETY Information – [cont’d]

Safety, Identification and Information Labels

Information labels affixed to the Allied equipment
include safety warnings, identification and
instructions important to operation and service.

Keep all safety labels clean. Words and illustrations
must be legible. Before operating this equipment,
replace damaged or missing labels. Refer to the parts
section for ordering information. Refer to Figure S-2
for their location on the equipment.

Table S.1 Label Illustration and Description

Label

Figure

Description

Read the Manual

- Directs personnel to the manual for further information

and instructions

Stay Clear -

Alerts personnel and by-standers to maintain a safe distance

from the Allied work tool during operation.

Hot Surface

- Identifies surfaces of the Allied work tool that become hot

during operation.

Lift Point-

Identifies approved lift points of the Allied work tool.

Operating Pressure

– Identifies the operating pressure. Refer to the manual

for further information.

Oil Fill

- Identifies the location for adding oil to reservoir.

Oil Level

- Identifies the location for checking the oil level.

Company Logo

– Is the Allied brand identifier and is a registered trademark

of Allied Construction Products, LLC.

Ho-Pac

Product Identification

– Ho-Pac is a registered trademark of Allied

Construction Products, LLC used for identifying the hydraulic vibratory plate
compactor / driver.

L10

4000

Model Identification

- Identifies the model of the Allied work tool.

L11

Made in USA

L12

Equipment Identification

– Contains Manufacturer’s Name and Address,

Product Name, CE compliance marking, Model Number, Serial Number,
Year of Manufacture, and Mass

ALLIED

102728

allied

102729

Содержание HO-PAC 4000













































Результаты поиска

Содержание HO-PAC 4000

Отзывы:

Похожие инструкции для HO-PAC 4000

Бренды по названию

Популярные бренды

Allied HO-PAC 4000, Инструкция по безопасности, эксплуатации, техническому обслуживанию и запасным частям.

Результаты поиска

Содержание HO-PAC 4000

Отзывы:

Похожие инструкции для HO-PAC 4000

Бренды по названию

Популярные бренды