Allied HO-PAC 4000 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 44

Allied HO-PAC 4000 Скачать руководство пользователя страница 29

Allied Construction Products, LLC www.alliedcp.com

19

TM574173_HP4000_18feb

10.0 Handling, Transport & Storage

WARNING

Crush hazard. Injury may result if the
Ho-Pac shifts or falls. Do not lift the Ho-
Pac by the mounting pins or whip hose.
Recommended lift points are identified
with the HOOK symbol. Lifting devices
must safely carry the loads to which they
will be subjected. Lift away from people.
Do not enter the danger zone while the
attachment is being lifted.

CAUTION

Crush hazard. Keep hands and feet
clear of crush points. Always use
sufficient blocking to avoid accidental or
sudden movement of the attachment.

10.1 Lifting & Transport

See Technical Data Section for the weight of the
work tool.

10.1.1 When the attachment is transported
independently of the carrier

1.

Remove all loose debris from attachment.

2.

If the swivel assembly is installed, lock swivel
position with bolt.

3.

Follow removal instructions in Section 7.

4.

Secure hoses to unit to avoid accidental damage.

5.

Lift attachment at recommended lift points. Refer
to the Safety Section of this manual for their
location.

6.

Stabilize and secure the attachment adequately
for transport.

10.1.2 When the attachment is transported while
installed on the carrier

1.

Remove all loose debris from attachment.

2.

If the swivel assembly is installed, lock swivel
position with bolt.

3.

Secure hoses to unit to avoid accidental damage.

4.

Inspect the mounting pins and hardware for
damage and integrity.

5.

Transport carrier in accordance with carrier
manufacturer’s recommendations.

10.2 Storage

Observe the following storage preparations.

x

Do not drain oil unless fluid degradation warrants
change. Keep the motor full of oil to protect
internal components.

x

Seal hydraulic connections to protect against
contamination

x

Store in upright position

x

Support the mounting frame with blocks to
minimize permanent sag in spring mounts.

x

Protect rubber components such as spring
mounts and hoses from exposure to direct
sunlight to reduce aging effects

x

Avoid wet or damp conditions to minimize rust

«
...
27
28
29
30
31
...
»

Содержание HO-PAC 4000













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды