Allied HO-PAC 4000 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 44

Allied HO-PAC 4000 Скачать руководство пользователя страница 14

Allied Construction Products, LLC www.alliedcp.com

4

TM574173_HP4000_18feb

3.0 Warranty Protection Summary [cont’d]

3.3 Allied Product Policies

In this manual, Allied recommends the use,
applications, maintenance and service consistent
with industry practices.

Allied assumes no responsibility for the results of
actions not recommended in this manual and
specifically the results of:

x

Improper installation, set-up, calibration

x

Carelessness / Incorrect operating methods

x

Inattention to re-lubrication and other
maintenance requirements

x

Misuse / Unapproved applications

x

Inadequate or absence of training

x

Use of non-genuine Allied replacement parts

x

Unapproved modifications

x

Use of grease, which is not or is only
conditionally pumpable

x

The use of a lubricant type that is unsuitable for
the application.

x

Contaminated lubricants.

x

Improper disposal of used or contaminated
lubricants.

The product is excluded from warranty if any of the
above conditions result in damage to the Allied
equipment, or the associated equipment or injury to
personnel. Such conditions will be determined by
Allied at its sole unfettered discretion.

«
...
12
13
14
15
16
...
»

Содержание HO-PAC 4000













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды