1.
No ringback is detected within the period of time determined by register S7.
2. Also sent when the modem auto-disconnects due to loss of carrier.
For X0, sent for the following conditions:
1. If busy tone detection is enforced, busy or circuit busy has been detected.
2. If dial tone detection is enforced or selected, dial tone has not been detected.
4 ERROR Sent during an attempt to execute a command line if any of the following conditions occur:
1. The command line contains a syntax error.
2. The modem cannot execute a command contained in the command line, i.e., the
command does not exist or is not supported.
3. A command parameter within the command line is outside the permitted range.
For X0, X1, X2, and X3, this message is sent instead of DELAYED and BLACKLISTED.
5 CONNECT 1200 The modem has connected to the line and either the line speed is 1200 bps and DCE speed
reporting is enabled, or the DTE speed is 1200 bps and DTE speed reporting is enabled.
6 NO DIALTONE For X2 and X4, the modem has been instructed to wait for dial tone during dialing but none is received.
When cellular phone interface is selected, indicates that cellular service is not currently available.
7 BUSY For X3 and X4, if busy tone detection is enforced, the busy (engaged) signal is detected on the
line when the modem is attempting to originate a call.
8 NO ANSWER The modem is attempting to originate a call if a continuous ringback signal is detected on the
line until the expiration of the timer S7.
9 CONNECT 600 The modem has connected to the line, the DTE speed is 600 bps, and DTE speed reporting is enabled.
10 CONNECT 2400 The modem has connected to the line and either the line speed is 2400 bps and DCE speed
reporting is enabled, or the DTE speed is 2400 bps and DTE speed reporting is enabled.
11 CONNECT 4800 The modem has connected to the line and either the line speed is 4800 bps and DCE speed
reporting is enabled, or the DTE speed is 4800 bps and DTE speed reporting is enabled
.
12 CONNECT 9600 The modem has connected to the line and either the line speed is 9600 bps and DCE speed
reporting is enabled, or the DTE speed is 9600 bps and DTE speed reporting is enabled.
13 CONNECT 7200 The modem has connected to the line at 7200 bps and DCE speed reporting is enabled.
14 CONNECT 12000 The modem has connected to the line at 12000 bps and DCE speed reporting is enabled
.
15 CONNECT 14400 The modem has connected to the line at 14400 bps and DCE speed reporting is enabled.
16 CONNECT 19200 The modem has connected to the line and either the line speed is 19200 bps and DCE speed
reporting is enabled, or the DTE speed is 19200 bps and DTE speed reporting is enabled.
17 CONNECT 38400 The modem has connected to the line, the DTE speed is 38400 bps, and DTE speed reporting is
enabled.
18 CONNECT 57600 The modem has connected to the line, the DTE speed is 57600 bps, and DTE speed reporting
is enabled.
19 CONNECT 115200 The modem has connected to the line, the DTE speed is 115200 bps, and DTE speed
reporting is enabled.
22 CONNECT 75TX/1200RX The modem has established a V.23 originate connection and line speed reporting is
enabled.
23 CONNECT 1200TX/75RX The modem has established a V.23 answer connection and line speed reporting is enabled.
24 DELAYED For X4, sent when a call fails to connect and the number dialed is considered 'delayed' due to
country blacklisting requirements.
32 BLACKLISTED For X4, sent when a call fails to connect and the number dialed is considered 'blacklisted'.
33 FAX A fax modem connection is established in a facsimile mode
.
35 DATA A data modem connection is established in a facsimile mode.
40 +MRR: 300 The modem has connected to the line at 300 bps and carrier reporting is enabled. (See S95 and Xn.)
44 +MRR: 1200/75 The V.23 backward channel carrier is detected and carrier reporting is enabled. (See S95 and Xn.)
Содержание Tornado 562 S II
Страница 1: ...Tornado 562 S II User Manual...
