Allied Telesis AT-8100L/8POE Скачать руководство пользователя страница 233 | Manualshive

Страница: 233 / 330

background image

AT-8100 Series Version 2.2.5.0 Web Interface User’s Guide

233



Source and destination UDP ports



VLAN IDs

IPv4 Address and

Mask

The mask of an IPv4 address is a decimal number that represents
the number of bits in the address, from left to right, that constitute the
network portion of the address. For example, the subnet address
149.11.11.0/24 has a mask of “24” for first the twenty-four bits of the
network portion of the address. The IP address and the mask are
separated by a slash (/); for example, “149.11.11.0/24.”

Actions

The action defines the response to packets that match the filtering criterion
of the ACL. There are three actions for ACLs:



Deny

— A deny action instructs ports to discard the specified ingress

packets.



Permit

— A permit action instructs ports to forward ingress packets that

match the specified traffic flow of the ACL. By default, all ingress
packets are forwarded by the ports.



Copy to mirror

— This action causes a port to copy all ingress packets

that match the ACL to the destination port of the mirror port.

How Ingress

Packets are

Compared

Against ACLs

Ports that do not have an ACL forward

all

ingress packets. Ports with one

or more deny ACLs discard ingress packets that match the ACLs and
forward all other traffic. A port that has one deny ACL that specifies a
particular source IP address, for example, discards all ingress packets
with the specified source address and forwards all other traffic. In
situations where a port has more than one deny ACL, packets are
discarded at the first match.

Since ports forward all ingress packets unless they have deny ACLs,
permit ACLs are only necessary in situations where you want a port to
forward packets that are a subset of a larger traffic flow that is blocked: for
example, a port that forwards only packets having a specified destination
IP address. A permit ACL specifies the packets with the intended
destination IP address, and a deny ACL specifies all traffic.

When ports have both permit and deny ACLs, you must add the permit
ACLs first, because packets are compared against the ACLs in the order
they are added to the ports. If a permit ACL is added after a deny ACL,
ports are likely to discard packets specified by the permit ACL, thus
causing them to block packets you want them to forward.

«
...
231
232
233
234
235
...
»

Содержание AT-8100L/8POE











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT-8100L/8POE

Бренд: Abocom Страницы: 11

Бренд: Abocom Страницы: 19

SISPM1040-582-LRT

Бренд: Lantronix Страницы: 2

Бренд: Lantronix Страницы: 7

Maestro E220 Series

Бренд: Lantronix Страницы: 25

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Бренд: D-Link Страницы: 53

Бренд: H3C Страницы: 21

Бренд: Ruckus Wireless Страницы: 102

EdgeLens INT10G8LR56

Бренд: Garland Страницы: 30

Net2Air Ins-40085-US

Бренд: Paxton Страницы: 4

Бренд: ZyXEL Communications Страницы: 215

Бренд: 4G Systems Страницы: 2

Бренд: Moxa Technologies Страницы: 51

Бренд: Lutron Electronics Страницы: 4

Бренд: NKE Страницы: 15

SmartSwitch 8-slot

Бренд: Cabletron Systems Страницы: 150

Бренд: Matrix Switch Corporation Страницы: 60

Wisenet XRN-6410RB2-24TB

Бренд: Hanwha Techwin Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды