ALLIANCE SWNNC2HP115TQ01 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 90

background image

Error Codes

Display

Description

Cause/Corrective Action

EC11

No Card Reader
Initialization

Communication is valid, but there is no card reader initialization. Power down, power
up and try again.

EC18

No Communica-
tion

Card reader is initialized, communication lost. Power down, power up and try again. If
error persists, replace control or card reader.

EC19

No Card Reader
Communication

Communication failure. Power down, power up and try again. If error persists, replace
control or card reader.

Right most deci-
mal point Lit

Network Commu-
nication Error

Communication problem. Wait for 1.5 minutes for error to clear. If error doesn’t clear,
power-down and power-up the machine. If error persists, replace control or network
board.

Right most deci-
mal point Lit

Water Leak Detec-
tion Error or Slow
Drain Detection
Error

Water leak test has detected a water leak during a cycle or slow drain is detected in the
drain step of a running cycle. The decimal point will remain lit after the error display
has expired. Clear the decimal point by pressing the START keypad three times within
five seconds or by cycling the power to the machine.

Right most deci-
mal point blinking

Machine ID Error

Machine ID is no longer communicating with the control. Check Machine ID connec-
tion.

ALArn

Break-in Alarm
Error

Check the service door and coin vault switches.

oFF

Break-in Alarm
Shutdown Error

Check the service door and coin vault switches.

E FL

Fill Error

Fill level is not reached within 30 minutes (or other programmed length of time) in
any fill step.

Coin Error

Coin Error

Invalid coin pulse or inoperative coin sensor. Check coin drop area and remove ob-
structions. If error persists, tampering may have occured. Evaluate security proce-
dures.

E id

Board ID

Incorrect replacement control. Replace user control or output board with the correct
part.

E dS

Brownout/Voltage
Configuration

Unexpected supply voltage. Check the harness connections between the user control
and the output board. If the user control was replaced, set dip switch #1 to the same
seting as the previous control. If reworking the machine to use a different voltage sup-
ply, the dip switch #1 setting may need to be changed. If the dip switch #1 setting is
changed, power down, power up and try again.

E nr

Drive/Output
Board Not Ready

Hardware failure. Try cycling power to machine before replacing output board.

E bS

Drive/Output
Board Shorted

Hardware failure. Try cycling power to machine before replacing output board.

En

Machine ID Errors

Table continues...

Error Codes

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

83

Part No. 204370ENR1

«
...
81
82
83
84
85
...
»

Содержание SWNNC2HP115TQ01



























































































Отзывы:

Нет отзывов

Похожие инструкции для SWNNC2HP115TQ01

Бренд: Jackson Страницы: 2

Бренд: Jackson Страницы: 2

Бренд: Jackson Страницы: 2

Glasswashers Delta 5

Бренд: Jackson Страницы: 2

Бренд: Majestic Appliances Страницы: 20

DW60M6050 Series

Бренд: Samsung Страницы: 112

Бренд: Meiko Страницы: 248

INDEPENDENT 2800

Бренд: Lavor Страницы: 124

Custom Front DFUD042

Бренд: Viking Страницы: 34

Бренд: Hanseatic Страницы: 86

YWNE52PP113TW01

Бренд: Alliance Laundry Systems Страницы: 50

Бренд: Ryobi Страницы: 17

Бренд: Infiniton Страницы: 67

Бренд: Maytag Страницы: 27

Бренд: Saturn Страницы: 12

FAV6800A Series

Бренд: Maytag Страницы: 13

Бренд: Sindelen Страницы: 16

Бренд: Russell Hobbs Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды