ALLIANCE SWNNC2HP115TQ01 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 90

background image

Entering the Manual Mode

How to Enter the Manual Mode

For programming, testing, and retrieving information from the
control, it is often necessary to enter the Manual Mode by follow-
ing the four simple steps below. For an overview of entering the
Manual Mode, refer to the flowchart on the following page.
1. If accessing Diagnostic Tests that take control of machine op-

eration, be sure the washer is in the Start or Ready Mode be-
fore continuing to step 2. If the washer is in an active cycle,
rapid advance through the cycle. Refer to

Rapid Advance

.

2. Coin Models through Serial No. 1810000001: Open the serv-

ice door. The coin vault switch must be closed.

3. All Other Models: Open the service door, if necessary, and

unplug bullet connector.

4. While pressing and holding the LIGHT keypad with one

hand, press the NORMAL keypad with the other hand.

5. The display will show

rAPid

.

6. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to scroll

through the options until the desired option appears in the dis-
play.

7. Press the START (enter) keypad.

NOTE: After entering Manual Mode, if no keypads
are pressed for 4.25 minutes, the control will return
to the previous mode of operation.

8. To exit, press the WARM ( < ) keypad. The control will revert

back to Ready Mode.

Manual Mode Navigation

Manual Mode is broken into five groups: Manual Programming,
Manual Read Audit, Manual Reset, Manual Rapid Advance and
Manual Diagnostics.

Manual Programming can only be turned on or off with an exter-
nal device or the network. Refer to the appropriate instruction
manual. Manual Rapid Advance and Manual Diagnostics can be
turned on and off using an external device, by manual program-
ming, or with the network.

By default, all groups are turned on.

The manual features available in each group are as follows (the
menu shown on the display in this mode is in parentheses).

• Manual Programming (

Prog

)

• Manual Read Audit (

AUdit

)

• Manual Reset (

rESEt

)

• Rapid Advance (

rAPid

)

• Manual Diagnostic Tests (

diAg

)

If a group is turned off, the display will change from the selected
feature to

oFF

when the START (enter) pad is pressed. An audio

signal will then sound for one (1) second and the display will re-
turn to the selected feature. The features in the group cannot be
entered.

Entering the Manual Mode

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

19

Part No. 204370ENR1

«
...
17
18
19
20
21
...
»

Содержание SWNNC2HP115TQ01



























































































Отзывы:

Нет отзывов

Похожие инструкции для SWNNC2HP115TQ01

Бренд: lancer Страницы: 50

Бренд: lancer Страницы: 33

Бренд: Hanseatic Страницы: 86

Бренд: Bradley Страницы: 25

Бренд: V-ZUG Страницы: 36

HDS 3.5/23-4M Eg

Бренд: Kärcher Страницы: 48

Бренд: PowerBoss Страницы: 36

Бренд: Heinner Страницы: 72

Бренд: Smeg Страницы: 14

Бренд: iLive Страницы: 53

Profile PDWT400R

Бренд: GE Страницы: 2

HDS 3.0/20-4 EA/EG

Бренд: Kärcher Страницы: 48

Бренд: Cam Spray Страницы: 13

WW80H5290E Series

Бренд: Samsung Страницы: 88

Бренд: Samsung Страницы: 112

Бренд: Samsung Страницы: 120

Бренд: Samsung Страницы: 336

Бренд: Samsung Страницы: 960

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды