ALLIANCE SWNNC2HP115TQ01 Скачать руководство пользователя страница 67

Страница: 67 / 90

5. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to change

the current status.

6. Press the START (enter) keypad when the correct value ap-

pears in the display. The new value is saved and the next op-
tion will appear in the display.

Out of Order

oUt

This option allows the owner to disable machine use by display-
ing an out of order message.
1. Control must be in Manual Mode. Refer to

How to Enter the

Manual Mode

2. Press the DELICATES (

∧

) or the COLD (

∨

) keypad until

Prog

appears in the display. Press the START (enter) keypad,

and

AtS 1

will appear in the display.

3. Press the DELICATES (

∧

) or the COLD (

∨

) keypad to scroll

through the programmable options until

oUt

appears in the

display.

4. When

oUt

appears in the display, press the START (enter)

keypad. The current Out of Order status will appear in the dis-
play.

= Option Enabled

oFF

= Option Disabled (factory default setting)

5. Press the DELICATES (

∧

) or the COLD (

∨

) keypads to

change the current status.

6. Press the START (enter) keypad when the correct value ap-

pears in the display. The new value is saved and the next op-
tion will appear in the display.

Programming Control

DO NOT COPY or TRANSMIT

Part No. 204370ENR1

Содержание SWNNC2HP115TQ01



























































































Результаты поиска

Содержание SWNNC2HP115TQ01

Отзывы:

Похожие инструкции для SWNNC2HP115TQ01

Бренды по названию

Популярные бренды

ALLIANCE SWNNC2HP115TQ01, Оригинальное руководство пользователя

Результаты поиска

Содержание SWNNC2HP115TQ01

Отзывы:

Похожие инструкции для SWNNC2HP115TQ01

Бренды по названию

Популярные бренды