ALLIANCE Metered Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 54

background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Operation

37

802702

To Insert Card

Insert card into opening. DO NOT remove the card
until the

REMOVE CARD

LED is lit.

Figure 47

Step 8: Start Washer

After vend price has been satisfied, push the

START

keypad. Door must be closed to start washer.

Figure 48

Indicator Lights

WASH

WASH

is lit at the beginning of a Wash cycle and will

remain lit until the Wash cycle is complete.

RINSE

RINSE

is lit at the beginning of the Rinse or Extra

Rinse cycle and will remain lit until the Rinse cycle is
completed.

SPIN

SPIN

is lit for all Spin cycles.

DOOR LOCKED

DOOR LOCKED

is lit whenever the door is locked.

The door cannot be opened when this light is on.

INSERT COIN/CARD

INSERT COIN/CARD

is lit to prompt the user to insert

coins or a card to satisfy the vend price. When

INSERT

COIN/CARD

is lit, the digits and decimal point show

the vend price remaining to be satisfied.

REMOVE CARD (Card Models Only)

REMOVE CARD

flashes after the

START

keypad has

been pressed and the vend has been deducted from the
card.

IMPORTANT: If washer fails to operate properly
after installation, make sure electrical service and
water supply faucets are turned on. Are all the
controls properly set? Have a qualified serviceman
refer to the wiring diagram (located inside of
washer control cabinet), check for broken, loose or
incorrect wiring.

NOTE: Once a cycle has started, the door can only
be opened by first unplugging the power cord and
waiting one minute.

M343I

H207I

H207I

HOT

WARM

PERM

PRESS

COLD

START

NORMAL

DELICATES

To reduce the risk of bodily injury, do not
remove laundry from washer until all lights
are out, and all moving parts have stopped.

W092

WARNING

«
...
37
38
39
40
41
...
»

Содержание Metered























































Отзывы:

Нет отзывов

Похожие инструкции для Metered

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

GFWH2400L Series

Бренд: GE Страницы: 52

Profile PTWN8055MMS

Бренд: GE Страницы: 101

Profile PTWN6050MWT

Бренд: GE Страницы: 2

Profile PTWN8055MMS

Бренд: GE Страницы: 46

Бренд: GE Страницы: 2

Profile WPRB9220

Бренд: GE Страницы: 20

Profile ENERGY STAR WPRE6150K

Бренд: GE Страницы: 2

Profile PTWN6050M

Бренд: GE Страницы: 24

Бренд: GE Страницы: 24

Бренд: GE Страницы: 80

Бренд: GE Страницы: 24

Бренд: GE Страницы: 52

SPACEMAKER WSKS3040E

Бренд: GE Страницы: 3

Бренд: Fagor Страницы: 30

Бренд: Gaggenau Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды