ALLIANCE Metered Скачать руководство пользователя страница 42

Страница: 42 / 54

Operation

802702

Step 7: Start Dryer

To start dryer, push

START

keypad.

To stop dryer at any time, open the door. To restart the
dryer, close door and push

START

keypad.

Cycle is completed when time remaining reaches
00 minutes.

Figure 56

Indicator Lights

START

START

is lit when the dryer is not in a cycle, the full

vend price has been satisfied and the dryer door is
closed. When the

START

keypad is pressed, the cycle

will begin or resume.

DRYING

DRYING

is lit to indicate that one of the heated cycles

(HIGH TEMP, MED TEMP, LOW TEMP or
DELICATES) is currently in operation.

DRYING

will

turn off at the end of a heated cycle or when the COOL
DOWN cycle begins.

COOL DOWN

COOL DOWN

is lit whenever the COOL DOWN

portion of a heated cycle is active. It is also lit when no
heat is programmed for a cycle in operation.

DRY1928N

DRY1

Содержание Metered























































Результаты поиска

Содержание Metered

Отзывы:

Похожие инструкции для Metered

Бренды по названию

Популярные бренды

ALLIANCE Metered, Руководство по установке и эксплуатации

Результаты поиска

Содержание Metered

Отзывы:

Похожие инструкции для Metered

Бренды по названию

Популярные бренды