ALLIANCE Metered Скачать руководство пользователя страница 4

Страница: 4 / 54

© Copyright 2008, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.

802702

Table of

Contents

Safety Information

..............................................................................

Explanation of Safety Messages ...........................................................

Important Safety Instructions ...............................................................

Installation

...........................................................................................

Before You Start ...................................................................................

Supplies............................................................................................

Installing the Unit ................................................................................. 10

Step 1: Position Unit Near Installation Area.................................... 10
Step 2: Connect Fill Hoses............................................................... 10
Step 3: (Non-Gravity Drain Models Only)

Connect Drain Hose to Drain Receptacle....................................... 12

Step 4: (Gravity Drain Models Only)

Connect Drain Outlet to Drain System........................................... 12

Step 5: (Gas Dryer Only) Connect Gas Supply Pipe ....................... 13
Step 6: (Electric Dryer Only) Connect Electrical Plug .................... 14
Step 7: Connect Dryer Exhaust System ........................................... 20
Step 8: Position and Level the Unit ................................................. 25
Step 9: (Washer Only) Remove the Shock Sleeves

and Shipping Brace ........................................................................ 27

Step 10: Wipe Out Inside of Washer Drum and Dryer Drum.......... 27
Step 11: Plug In the Washer and Dryer ........................................... 28
Step 12: Recheck steps 1-11 ............................................................ 30
Step 13: Check Heat Source ............................................................ 30

Operation

............................................................................................. 32

Operation Instructions for MDC Washers ............................................ 32

Operation Instructions for NetMaster Washers .................................... 35

Содержание Metered























































Результаты поиска

Содержание Metered

Отзывы:

Похожие инструкции для Metered

Бренды по названию

Популярные бренды

ALLIANCE Metered, Руководство по установке и эксплуатации

Результаты поиска

Содержание Metered

Отзывы:

Похожие инструкции для Metered

Бренды по названию

Популярные бренды