allen MP245 Скачать руководство пользователя

Страница: 50 / 106

SECTION 3

SERVICE

067975

Page 50

Transporting Trowel Procedures

Optional dolly jacks are available for short moves or to aid in servicing the trowel.

Install dolly jacks as follows:

Inspect dolly jack for serviceability and damage.

Place riding trowel on firm level ground.

Tie steering levers

[I]

(if applicable) to frame to prevent them from tipping for-

ward when trowel is being lifted. AEC assumes no liability if injury occurs and

this step is eliminated during any trowel lifting procedures.

Insert the front dolly jack

[J]

fully into the holes in the mainframe of the riding

trowel. The front dolly jacks are equipped with short lifting tubes while the rear

dolly jacks have long lifting tubes.

Insert the rear dolly jack

[M]

with the long lifting tubes into the holes

provided in the rear of the mainframe. The holes in the mainframe are located

directly opposite the front holes.

Turn jack handles clockwise to lift trowels and counter-clockwise to lower

trowel.

[I]

Transporting Trowel

PICTURE FOR REFERENCE ONLY

Содержание MP245











































































































Результаты поиска

Содержание MP245

Отзывы:

Похожие инструкции для MP245

Бренды по названию

Популярные бренды

allen MP245, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MP245

Отзывы:

Похожие инструкции для MP245

Бренды по названию

Популярные бренды