allen MP245 Скачать руководство пользователя страница 37

Страница: 37 / 106

SECTION 2

OPERATIONS

067975

Page 37

Starting Procedures

Before starting riding trowel, refer to figures below for location and identification of opera tional and visual controls per

taining to the operation of the riding trowel.

1. Sit down correctly on the riding trowel seat. DO NOT attempt to start the riding trowel without an operator in the seat.

2. If engine is cold, pull out the choke lever. Press down on throttle pedal (located by the operator’s right foot) one to two

times.

To much throttle during start-up will flood the engine.

3. Turn ignition switch key to the start-position, immediately release key when engine starts. If after two or three attempts

the engine has not started push in choke. Attempt to start trowel again. Allow engine to warm up for 5 minutes before

operating riding trowel.

Operating the starter for more than 5 seconds can damage the starter or engine. If engine fails to start release the switch

and wait 15 seconds before operating starter again.

Pre Operating Instructions (cont’d)

Содержание MP245











































































































Результаты поиска

Содержание MP245

Отзывы:

Похожие инструкции для MP245

Бренды по названию

Популярные бренды

allen MP245, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MP245

Отзывы:

Похожие инструкции для MP245

Бренды по названию

Популярные бренды