allen MP245 Скачать руководство пользователя страница 24

Страница: 24 / 106

SECTION 1

SAFETY

067975

Page 24

●

ALWAYS

keep the machine in proper running condition.

● Fix damage to machine and replace any broken parts immediately.

●

ALWAYS

store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of

the reach of children and unauthorized personnel.

●

DO NOT

place hands or fingers inside engine compartment when engine is running.

●

NEVER

operate the engine with heat shields or guards removed.

● Keep fingers, hands hair and clothing away from all moving parts to prevent injury.

●

DO NOT

remove the engine oil drain plug while the engine is hot. Hot oil will gush out of the oil tank and severely scald

any persons in the general area of the screed.

●

NEVER

touch the hot exhaust manifold,

muffler or cylinder. Allow these parts to cool
before servicing equipment.

●

NEVER

run engine without an air filter or with a dirty air filter. Severe engine damage may occur. Service air filter frequent

ly to prevent engine malfunction.

●

NEVER

tamper with the factory settings of the engine or engine governor.

Damage to the engine or equipment can result if operating in speed ranges
above the maximum allowable.

General Safety (cont’d)

Содержание MP245











































































































Результаты поиска

Содержание MP245

Отзывы:

Похожие инструкции для MP245

Бренды по названию

Популярные бренды

allen MP245, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MP245

Отзывы:

Похожие инструкции для MP245

Бренды по названию

Популярные бренды