allen MP245 Скачать руководство пользователя

Страница: 35 / 106

SECTION 1

SAFETY

067975

Page 35

Use the appropriate set of jacks that are designed for the machine you

are lifting.

STEP 1:

Attach the front and rear dolly jacks into the machine at the receiving

tube locations.

STEP 2:

Slowly lift machine in a safe manner to a height that is required to

safely install the pans. This is typically 6-8” above floor level.

STEP 3:

Carefully slide the pans under the machine making sure that you are

aware of the corners on the blades that are sharp. (B)

STEP 4:

Align the pans so that the clips will not be crushed when the machine

is lowered back down.

STEP 5:

Slowly lower the machine down onto the pans while maintaining a

visual so the blades are going into the proper gaps. (Typically the pans can

only be intalled one way)

STEP 6:

Remove lifting bridle from the machine.

STEP 7:

Start machine and slowly increase the throttle until the blades slowly

begin turning and engaging the pans. The machine is now ready to finish con

crete utilizing the pans.

NOTE:

Utilizing the lifting sling(bridle) and the dolly jacks are intended only for

site transportation and the installation of pans and blades. DO NOT use them
for regular maintenance without the additional use of jack stands to insure
stability of the machine.

Pan Installation Instructions (cont’d)

Содержание MP245











































































































Результаты поиска

Содержание MP245

Отзывы:

Похожие инструкции для MP245

Бренды по названию

Популярные бренды

allen MP245, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MP245

Отзывы:

Похожие инструкции для MP245

Бренды по названию

Популярные бренды