allen MP245 Скачать руководство пользователя

Страница: 34 / 106

SECTION 1

SAFETY

067975

Page 34

Use a lifting sling (bridle) with a capacity of at least a 2:1 weight ratio for the equip-

ment being hoisted.

STEP 1:

Attach the lifting bridle to the machine at all four lifting points.

STEP 2:

Slowly lift machine in a safe manner to a height that is required to safely install

the pans. This is typically 6-8” above floor level.

This section details the proper technique to utilize the lifting bridle system and the dolly jack system in a safe
manner to install pans. (NOTE: Images are for illustration purposes only)

STEP 3:

Carefully slide the pans under the machine making sure that you are aware of the

corners on the blades that are sharp.

STEP 4:

Align the pans so that the clips will not be crushed when the machine is lowered

back down.

STEP 5:

Slowly lower the machine down onto the pans while maintaining a visual so the

blades are going into the proper gaps. (Typically the pans can only be intalled one way)

STEP 6:

Remove lifting bridle from the machine.

STEP 7:

Start machine and slowly increase the throttle

until the blades slowly begin turning and engaging the

pans. The machine is now ready to finish concrete
utilizing the pans.

Pan Installation Instructions

Содержание MP245











































































































Результаты поиска

Содержание MP245

Отзывы:

Похожие инструкции для MP245

Бренды по названию

Популярные бренды

allen MP245, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MP245

Отзывы:

Похожие инструкции для MP245

Бренды по названию

Популярные бренды