allen MP245 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 106

background image

SECTION 2

OPERATIONS

067975

Page 39

With the operator in the seat, show them the functions of the joysticks [B] and [C] and how to start the machine.

A hard level concrete slab with water on the surface is an ideal place for an operator to practice with the machine. For prac

-

tice pitch the blades up approximately 1/4 inch on the trailing edge. Start by making the machine hover in one spot and then
practice driving the machine in a straight line and making 180 degree turns. Best control is achieved at full engine RPM.

After starting engine fully engage the throttle. This allows the engine to warm up quicker and also engages the torque con

-

verter. At this time the machine’s rotors will begin turning.

DO NOT

use excessive pressure on the joysticks. Excessive pressure does not increase the reaction

time of the machine and can damage steering controls.

Stopping The Riding Trowel

To stop the trowel’s movement, let go of the joysticks [B] and [C]. They will return to their neutral position. Also release
pressure on the right foot pedal [E].

This machine has a kill switch mechanism installed in the seat. If in need of an emergency stop, simply lifting the foot off
of the throttle pedal will stop the rotors from turning immediately.

Operating Instructions (cont’d)

«
...
37
38
39
40
41
...
»

Содержание MP245











































































































Отзывы:

Нет отзывов

Похожие инструкции для MP245

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды