Allen-Bradley 8720MC Скачать руководство пользователя страница 106

Страница: 106 / 128

106

Rockwell Automation Publication 8720MC-RM001K-EN-P - September 2018

Chapter 8

Troubleshoot the 8720MC-RPS Unit

Operation Flow Charts

These flow charts track the 8720MC-RPS unit power-up sequencing to make
sure that the unit has power applied and that the DC-bus is at an acceptable
voltage level.

Figure 47 - 8720MC-RPS Unit Fails to Power Up

The 8720MC-RPS unit

does not run.

Is AC power applied to the

8720MC-RPS unit?

RUN sequence

input entered?

Is Precharge

complete?

Is the main magnetic

contactor operating?

Check the following:
• Circuit breaker
• Protection fuse
• Wiring
• Power supply

The 8720MC-RPS unit is

defective. Replace the unit.

Check wiring for the sequence signals.

Check the following:
• Setting of the Precharge/Discharge Time (F.014)
• Precharge/Discharge resistor and associated wiring

Check the following:
• Wiring for sequence signals
• Wiring to main magnetic contactor coil
• Order of phases of wiring for main power supply

and control power

Yes

Содержание 8720MC

































































































































Результаты поиска

Содержание 8720MC

Отзывы:

Allen-Bradley 8720MC, Руководство пользователя, Страница: 106 / 128

Результаты поиска

Содержание 8720MC

Отзывы: