ALL-O-MATIC SL-100 DC Скачать руководство пользователя страница 25

Страница: 25 / 44

1 2 3 4 5 6 7 8

-----------------------OPEN------------------------

TIMER

RADIO

OSC

FAIL SC/SF

1-PASS

SLAVE

AUTO OPEN

OPEN L/R

OFF ON

NOTE:

IF ANY CHANGES ARE

MADE TO THE DIPSWITCHES

WITH THE POWER ON, PRESS

THE

MAIN RESET

BUTTON TO

RECOGNIZE THE CHANGES.

TIMER

switch

“ON”

activates the automatic close

timer.

RADIO

switch

“ON”

allows the radio receiver to

override the automatic close timer.

OSC

switch

“ON”

allows the radio receiver to stop

and reverse the gate in any direction. During a cycle,

the ﬁrst signal stops the gate. A second signal

reverses the gate.

FAIL SC/SF

for

Fail-Safe

: Upon power failure, board will monitor

battery voltage to make sure gate opens before battery

completely drains.

OFF

for

Fail-Secure

: Upon power

failure, gate will run until battery is low and lock closed.

1-PASS

switch

“ON”

allows the gate to open until

one vehicle goes over the safety loop. Once the

vehicle has cleared the loop, the gate will stop and

close. If a second vehicle goes over the loop while

the gate is closing, the gate will stop. The vehicle

must get off of the loop before the gate continues to

close, forcing the second vehicle to present valid

credentials. This is a true one pass, anti-tailgating

feature to be used with safety loops.

SLAVE

This feature is used in dual gate applications. The

SLAVE

switch will be

“ON”

only on the slave

operator. All other dip switches will be “off”.

SLAVE

switch will be

“OFF”

on the master operator. Set

desired dip switch settings on the master operator

only.

AUTO OPEN

This feature is to automatically open the gate on

power interruption. It is a very particular feature

used in areas where the fire department requires the

gate to open automatically after a power outage.

Set this dip switch “ON” when this feature is desire.

OPEN L/R

switch

“ON”

is used for right hand

opening of the gate. The

“OFF”

position is used

for left hand opening of the gate.

RESET

DIP SWITCH FUNCTIONS

Содержание SL-100 DC













































Результаты поиска

Содержание SL-100 DC

Отзывы:

ALL-O-MATIC SL-100 DC, Руководство пользователя, Страница: 25 / 44

Результаты поиска

Содержание SL-100 DC

Отзывы: