Algas SDI TORREXX TX240 Скачать руководство пользователя страница 21

Страница: 21 / 93

ASDI

Operations and Maintenance – TX Models – P/N: 54629

3-14

SAFETY RELIEF VALVE

If the vaporizer is to be installed within an enclosure or building,

vent th

e safety

relief valve outside the enclosure and re

direct the discharge

upwards

. A

pipe-away adapter must be used at the relief valve. Always install a rain-cap or

similar device to prevent water and other debris from entering the relief valve. If

water enters, it may freeze and prevent the relief valve from properly discharging,

creating a potentially hazardous situation.

ELECTRICAL SERVICE

The rating plate on the vaporizer and the data sheet provided with the manual

provides your specific vaporizer’s electrical power requirements and the drawing

numbers of the appropriate wiring diagrams and schematics. This unit is

constructed to meet ATEX/IECEx Zone I requirements (depending on model). All

wiring to the unit, including the ground connection, must meet the applicable

codes for the area in which it is being installed and with approved connectors.

Internally a ground connection is provided by the factory. Wire size and type

must comply with the applicable codes for the area in which it is being installed.

Tables

through

list the recommended wire size for the different models and

are to be used as guides only. Provide a fused disconnect or circuit breaker

outside of the classified area. If it is not within sight of the vaporizer, the fused

disconnect must have a locking device. Run wire within rigid conduit and install a

seal-off at the connection of the field conduit to the vaporizer. For Zone 1

locations, the unused entry size is 1” NPT with factory supplied M32x1.5 adapter.

Each vaporizer shall have a

separate disconnect.

If the installation is prone to surges it is recommended to protect the equipment

by installing a properly sized Semiconductor or “ultra-fast acting” fuse in each

phase upstream of the TORREXX

that has a total clearing I

t rating of less than

18,000 A

sec.

GROUNDING

INTERNAL

Internal ground connection is required. Use the grounding connection in the

respective enclosure where the power is supplied. A factory provided #8 AWG

(3.26 mm diameter or 8.3 mm

cross sectional area) wire is permanently secured

to the enclosure. Use a dual rated (Al/Cu) and dual barrel lug connector to make

the connection between the factory and field ground wires. Reference lug

connector manufacturer’s recommendation for tightening moment. Alternatively,

crimp a dual rated (Al/Cu) ring connector to the factory provided ground wire and

make a connection at the provided junction box terminal. Reference ring

connector manufacturer’s recommendation for proper crimping tools and

technique. Reference junction box manufacturer’s recommendations for

tightening moment.

EXTERNAL

External ground connection is optional. At the back of the enclosure base an

external ground hole measuring 0.17 in (4.3 mm) in diameter is provided. Use a

5/32 in (0.156 mm) diameter blind aluminum rivet and a dual rated (Al/Cu) ring

connector to connect the external ground wire to the enclosure attachment.

Verify all

ground connections are secure.

Содержание TORREXX TX240






























































































Результаты поиска

Содержание TORREXX TX240

Отзывы:

Похожие инструкции для TORREXX TX240

Бренды по названию

Популярные бренды

Algas SDI TORREXX TX240, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание TORREXX TX240

Отзывы:

Похожие инструкции для TORREXX TX240

Бренды по названию

Популярные бренды