background image

 

  

 

 

 

 

Figure 2.4: Draining smoke to the outer wall

 

of the chimney

    

Figure 2.5: Draining smoke to the roof through a traditional 

chimney 

 

It is recommended that you follow the guidelines set forth in the standards in relation to the size and radius of the chimney 

(C). In any case, never use an exhaust duct with an inner radius smaller than 100 mm. 

In the case of the exhaust ducts of greater radius, there must be a steel pipe (A) within the funnel bricks or mortar (C), as 

shown in Figure 2.6. 

The steel pipe must be insulated using a suitable heat-resistant material, such as rock wool or vermiculite (B), and it 

must be separated from the outer part of the funnel. 

 

Figure 2.6: An example of connection to the chimney 

In case of fire in the chimney or stovepipe, immediately turn off the furnace and disconnect it from the electrical system. 

 

 

Dismantling and waste disposal

 

 

The packaging consists of materials which are not toxic or harmful. No special conditions are needed for its disposal. 

The user is responsible for the disposal of the remaining components of the packaging. The user must follow the proper 
disposal procedures in accordance with the applicable standards in the country where the product is assembled. 

 ATTENTION: The packaging elements must be kept out of reach of children who are not supervised or out of reach of 

persons with disabilities. 

 

 

Electrical connections

 

 

The product can be connected to the mains only after the electrical insulation is assembled. 

Connect the product to your household power. 
Just press the main switch on the back of the appliance if you want to turn it on. When you do this the furnace will be 

ready for ignition. For ignition procedures and programming, refer to section 4. 

 

 

Room temperature gauge 

Room temperature gauge can be adjusted only after setting up the electrical installation

.

 

This gauge allows the temperature in the room where the furnace is placed to be continuously monitored. 

Placing the room temperature gauge in a suitable spot will ensure proper operation of the product. 

 

Using the Product 

 

Содержание LUCA 12





























Отзывы: