manualshive.com logo in svg

Alfa Laval Toftejorg MultiJet 65, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval Toftejorg MultiJet 65 Скачать руководство пользователя страница 37

7 Trouble shooting guide

MultiJet 65

Slow rotation or failure of machine to rotate

Possible Causes

Fault finding

No or insufficient liquid flow

a). Check if supply valve is fully open
b). Check if inlet pressure to machine is correct
c). Check supply line and filter for restriction/clogging
d). Remove Nozzles and check for clogging. If blocked, carefully clean Nozzle
without damaging stream straighteners and Nozzle tip.
e). Remove Flange/Nipple, Guide and Impeller (see page 22) and check for
clogging in Impeller area.
If large particles repeatedly get jammed in the machine, install filter or reduce
mesh size of installed filter in supply line.

Foreign material or material build-up

Insert hex Screwdriver in Screw in top of Turbine shaft and easily turn Turbine
shaft clockwise. If any resistance is recognised, disassemble machine in order
to localise the cause.

a). Impeller jammed

Remove Guide and Impeller (see page 22) and remove foreign material.

b). Turbine shaft sluggish in Main bush

Remove Gear Subassembly with Turbine shaft (see page 30) and Gland (pos. 5)
and clean Main bush.

c). Bevel gears jammed

Remove Flange/Nipple and Hub Assembly (see page 26). Clean teeth on
Stem and Bevel gear.

d). Stem jammed/sluggish

Remove Gear subassembly (see page 30). Check free rotation of Stem.
Remove Stem (see page 28). Remove foreign material/material build-up on
Stem and inside Main collars. Clean Ball races and Ball retainer with balls.
Also clean main bush.

e). Gearbox jammed/sluggish

Remove foreign material from Gearbox. Check sluggish rotation of shafts. If
restriction is recognized, disassemble Gear subassembly (see page 30) and
remove material build up, especially on 2. Stage Worm wheel and mating Collar
bushes.

f). Hub jammed/sluggish

Disassemble Hub Assembly (see page 26). Remove foreign material inside Hub.
Clean Ball races and Ball retainer with balls. Also clean nose of Body.

Wear
a) Slide bearings

See page 21.

b) Main bush

See page 21.

c) Worm wheels

See page 21.

d) Collar bushes

See page 21.

e) Turbine shaft

Check clearance in Main bush and in Slide bearing. Transverse movement
should not exceed 0.5 mm. Also inspect Worm wheel for wear.

f) Horizontal shaft

Check clearance in Collar bushes. Transverse movement should not exceed
0.5 mm. Also inspect worm for wear.

Mechanical defects
a). Worm wheels. Teeth broken

Replace Worm wheel.

b). Worm wheel can rotate on Horizontal
shaft/Pinion due to damaged driver faces.

Replace Worm wheel.

c). Damaged teeth on Bevel gear

Inspect teeth on Stem and Hub for deformation. Mount Hub and Stem in Body
(see page 26 and 28). Hold Body in upside down position and rotate Hub to
check that Bevel gears can work together. If damaged: Replace Stem and/or
Bevel gear.

37

Содержание Toftejorg MultiJet 65

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды