manualshive.com logo in svg

Alfa Laval Toftejorg MultiJet 65, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval Toftejorg MultiJet 65 Скачать руководство пользователя страница 36

6 Maintenance

MultiJet 65

6.10

Replacement of main collars

Although normally exposed to very limited wear, it is possible to replace Main collar (pos. 28.2) in Body. The procedure to
do this is described below.

Warning:

Replacement of Main collars involves risk of damaging the special threads and accordingly the body. It is
recommended to let an authorized Alfa Laval sales office do the replacement.

Main collar lower
1. Place Body (pos. 28) in a vice upright position. Do not clamp on machined faces. Insert tool (see page 53) into Main collar

(pos. 28.1). To loosen Loctite, knock hard on tool with hammer. Unscrew Main collar.

2. Carefully clean thread and recess in Body. Do not damage special thread in Body. Recess must be absolutely clean and free

from remains of old Loctite. If desired, use solution of ethylene glycol.

3. Make sure that new Main collar is clean and free from impurities. Apply Loctite No. 243 on thread.
4. Screw in new Main collar. Attention should be given to make sure that thread is in correct engagement before screwing

in Main collar.

5. Tighten Main collar fully home. Several times knock hard on tool and tighten up.

Warning:

Thread on Main collar is left-handed.

Replacement of Main Collars

4109-0034

36

Содержание Toftejorg MultiJet 65

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды