Alfa Laval Toftejorg MultiJet 65 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 56

background image

6 Maintenance

MultiJet 65

6.5

Hub subassembly

Disassembly
1. Remove Nozzles (pos. 22). Nozzles are untightened with a wrench on the faces of the Nozzles.
2. Remove Screws (pos. 17) and Spring washer (pos. 16) from Hub cover (pos. 21).
3. Draw out Hub Subassembly. If Hub cover (pos. 21) clings into Body, knock carefully with plastic hammer on outer diameter

to loosen.

4. Remove Cotter pin (pos. 24). Unscrew contra clockwise Hub conical part (pos. 23) freeing Hub cover (pos. 21), Ball retainer

w. balls (pos. 27) and Bevel gear (pos. 20). To unscrew Hub conical part (pos. 23), Hub nozzle part (pos. 25) is held in a vice.
Caliper (tool No. TE369) is used for the unscrewing using the two holes in end face of Hub conical part.

Note: Left-hand thread

If Ball races (pos. 26) in Hub cover and in Bevel gear are extremely worn, they should be replaced as well as the Ball retainer
with balls (pos. 27). How to replace Ball races see page 34.

If blue liners on Stem are extremely worn, they can be replaced. This part requires that a precise procedure is followed to
accomplish installation. It is highly recommended that an authorized Alfa Laval Tank Equipment Service Center perform the
replacement when necessary. Alternatively, in many cases it is possible to purchase a complete Stem With Liners mounted for
your machine.

Reassembly
1. Mount Bevel gear (pos. 20), Ball retainer with balls (pos. 27) and Hub cover (pos. 21) on Hub conical part (pos. 23). Screw

on Hub nozzle part (pos. 25). Note: Left-handed thread. To tighten, place Hub nozzle part in a vice and use Caliper (tool No.
TE369). Tighten until holes are aligned to pass Cotter pin (pos. 24). Insert Cotter pin and split (preferably new cotter pin).

2. Slide on Hub Subassembly, fit Hub cover (pos. 21) into Body and mount Spring washers (pos. 16) and Screws (pos. 17).
3. Screw on Nozzles (pos. 22) and tighten with wrench. If desired secure with Loctite No. 242 or equivalent.

26

«
...
24
25
26
27
28
...
»

Содержание Toftejorg MultiJet 65

























































Отзывы:

Нет отзывов

Похожие инструкции для Toftejorg MultiJet 65

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

Бренд: Pari Страницы: 282

Бренд: Saadat Страницы: 61

Бренд: Saadat Страницы: 22

Бренд: VADDIO Страницы: 58

Бренд: Abus Страницы: 12

Бренд: KCI Страницы: 2

Бренд: KCI Страницы: 60

Бренд: Landoll Страницы: 38

Бренд: Zimmer Страницы: 2

Бренд: ZipRip Страницы: 31

Бренд: Sota Страницы: 7

Бренд: GE Страницы: 241

Бренд: GE Страницы: 223

Бренд: GE Страницы: 644

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды