background image

Operating Manual

1 D
Minimum

½ D
Minimum

4.3  Installation

Before the pump is installed it is advisable to
consider the following:

Always -

Ensure that the mounting
surface is flat to avoid distortion
of the pump and drive unit.

Always -

Allow at least one metre for
pump access/maintenance all
around the pump.

Ensure that there is an
adequate electrical supply
close to the pump drive unit.
This should be compatible with
the electric motor selected.

4.2  Pump and Base Foundations

Depending on your requirements the pump

and drive (if supplied) may arrive mounted on
a baseplate.  Our standard baseplates have
pre-drilled fixing holes to accept base retaining
bolts.
To provide a permanent, rigid support for
securing the pump unit a foundation is required,
this will also absorb vibration, strain or shock on
the pumping unit.

Foundation Size

The foundation should be approximately
100mm longer and wider than the mounting
base of the unit.  The depth of the foundation
should be proportional to the size of the pump
unit.  (Pump coupled to drive unit.)

Bolt Location Dimensions

The location and sizes of the relevant bolting
down holes can be provided on a certified
drawing from your supplier.

Typical Foundation Bolts

The drawing below shows two methods for
foundation bolt retaining.  The sleeve allows for
'slight' lateral movement of the bolts after the
foundation is poured.  Use rag or paper to
prevent the concrete from entering the sleeve
while the foundation is poured.  A minimum of
14 days is required to allow the airing of the
concrete prior to operation.

D = Diameter of foundation bolt

Electrical -
Supply

10

Содержание N Series





































Отзывы: