Alfa Laval N Series Скачать руководство пользователя

Страница: 10 / 36

Operating Manual

All warnings in this manual are summarised on
this page.

Pay special attention to the instructions below
so that severe personal injury or damage to the
pump can be avoided.

Personnel performing installation, operation
and maintenance of the pump must have the
relevant experience required.

INSTALLATION

OPERATION

MAINTENANCE

: Always

observe the technical data.

: The pump

must

be electrically connected by authorised personnel. (See the motor

instructions supplied with the drive unit).

: Never

start in the wrong direction of rotation with liquid in the pump.

Never

put your hands or fingers inside the port connections

1.5 Safety Requirements

Warnings Signs:

General safety instructions are
preceded by this symbol.

Electrical safety instructions are
preceded by this symbol.

Take great care when using caustic
agents.

: Always

observe the technical data.

: Never

touch the pump or the pipelines when pumping hot liquids.

: Never

stand on the pump or pipelines.

: Never

run the pump with both the suction side and the pressure side blocked.

: Always

handle toxic and acidic liquids with great care.

Never

put your hands or fingers inside the port connections.

: Always

observe the technical data.

: Always

disconnect the pump from the drive unit and power supply when servicing

the pump.

: The pump must

never

be hot when servicing it.

: The pump and pipelines must

never

be pressurised when servicing the pump.

Never

put your hands or fingers inside the port connections.

STUDY THIS MANUAL CAREFULLY

Содержание N Series





































Результаты поиска

Содержание N Series

Отзывы:

Похожие инструкции для N Series

Бренды по названию

Популярные бренды

Alfa Laval N Series, Руководство по эксплуатации

Результаты поиска

Содержание N Series

Отзывы:

Похожие инструкции для N Series

Бренды по названию

Популярные бренды