background image

NOTICE

 

INSTALLATION

CHAUFFÉO-CHAUFFÉO+

Chauffe-eau électrique

Electric water heater - Elektrische boiler 

F

EN

NL

NOTICE D’UTILISATION 

ET D’INSTALLATION 

Installation and operating manual   

Installatie- en gebruiksvoorschriften 

À conserver par l’utilisateur

Manual must be kept by end user
Richtlijnen te bewaren door de gebruiker

www.atlantic.fr

Edition Fé

vrier 2

0

21

CERTIFICAT DE GARANTIE

À CONSERVER PAR L’UTILISATEUR DE L’APPAREIL

DURÉE DE GARANTIE

• 5 ans pour la cuve des chauffe-eau de 50 à 500 L et leur porte bougie.

• 2 ans pour les équipements amovibles : joint de porte, élément chauffant, thermostat…

WARRANTY CERTIFICAT

E - To be kept by the end user - Warranty period:

• 5 years for the 50 to 500 L water heater tanks and their heating element sheaths.

• 2 years for removable equipment: door seal, heating element, thermostat, etc.

GARANTIEBON

 - Te bewaren door de gebruiker van het toestel - Garantieduur:

• 5 jaar op de kuip en de verwarmingselementhuls van de boilers.

• 2 jaar op demonteerbare onderdelen: deurafdichting, verwarmingselement, thermostaat…

BIP

Rue Monge - BP 65

F-85002 LA ROCHE SUR YON

International : consultez votre installateur  

Raadpleeg uw installateur

•  Le remplacement d’un composant ou d’un produit ne peut en aucun cas prolonger la durée initiale de la garantie. 
•  Notre responsabilité ne saurait être engagée pour des dommages causés par une mauvaise installation ou par le non-respect des 

instructions se trouvant dans le document. 

ATTENTION :

 Un produit présumé à l’origine d’un sinistre doit rester sur site à la disposition des experts d’assurance et le sinistré doit en 

informer son assureur. Tout remplacement doit se faire en accord avec l’assurance.

•  Replacement of any component or product will in no case result in the extension of the initial warranty period. 
•  Atlantic is not liable for damage caused by improper installation or failure to follow the instructions in this document. 

WARNING:

 In the case of an insured event, the product must be made available to claims adjusters and the victim must inform their 

insurance provider. The insurance provider must approve any replacement.

•  De vervanging van een onderdeel zal in geen geval leiden tot verlenging van de oorspronkelijke garantieperiode. 
•  Wij kunnen onder geen beding aansprakelijk worden gesteld voor schade die voortvloeit uit een verkeerde installatie of de 

niet-naleving van de instructies in het document. 

OPGELET:

 Indien wordt verondersteld dat een product aan de oorzaak ligt van de schade, moet dit ter beschikking gehouden 

worden van de experten van de verzekering en het slachtoffer moet de schade melden aan zijn verzekering. Een vervanging kan enkel 
gebeuren met het akkoord van de verzekering.

DATE D’ACHAT : 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Purchase date / Aankoopdatum

NOM ET ADRESSE DU CLIENT : 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Client name and address / Naam-Adres

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MODÈLE ET N° DE SÉRIE : 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

À relever sur l’étiquette signalétique du chauffe-eau
Located on the water heater’s identification label
Model en serienummer overnemen van het identificatielabel van de boiler 

Cachet du revendeur

Retailer stamp / Stempel van de handelaar

La sérénité s’installe chez vous

ATLANTIC EST UNE MARQUE FRANÇAISE

U0695761

Summary of Contents for 021116

































































































Reviews: