Alfa Laval LKHex-10 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 46

Alfa Laval LKHex-10 Скачать руководство пользователя страница 31

6 Technical data

It is important to observe the technical data during installation, operation and maintenance.
Inform personnel about the technical data.

6.1

Technical data

The LKH pump is a highly efficient and econominal centrifugal pump, which meets the requirements of sanitary and gentle
product treatment and chemical resistance. The LKH pump is available in the following sizes LKHex -10, -15, -20, -25, -35, -40,
-45, -50, -60 and -70. The instruction manual is part of the delivery. Study the instructions carefully. The large pump sizes are
very heavy. Alfa Laval therefore recommends the use of a lifting crane when handling the pump.

Materials

Product wetted steel parts

AISI 316L

Other steel parts

Stainless steel

Finish

Semi-bright

Product wetted seals

EPDM (standard)

Other O-rings

EPDM (standard)

Alternative seals

Nitrile (NBR), fluorinated rubber (FPM) and FEP

Material, stationary seal ring

Acid-resistant steel with sealing surface of silicon carbide

Material, rotating seal ring

Carbon (standard) or silicon carbide

Shaft seal

Max. temperature flush media

70°C

Motor

Foot-flanged motor acc. to IEC metric standard 2 poles = 3000/3600 rpm at 50/60 Hz

4 poles = 1500/1800 rpm at 50/60 Hz

Motor sizes (kW), 50/60 Hz

1.5 - 75 kW

If a Variable Speed Drive (VFD) is required, only Exd and Exde motors can be used. This must be specified when ordering the
pump. If VFD is used, the motor should be oversized by 10 %.

For futher information, see PD sheet.

31

PH: 403.720.0999

«
...
29
30
31
32
33
...
»

Содержание LKHex-10















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды