manualshive.com logo in svg

Alfa Laval LKHex-10, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval LKHex-10 Скачать руководство пользователя страница 29

5 Maintenance

Read the instructions carefully. The items refer to the parts list and service kits section.
Lubricate the rubber seals before fitting them.

: Relates to the shaft seal.

5.5

Adjustment of shaft (LKHex-10 to -70)

Step 1
1. Loosen screws (6).
2. Pull off stub shaft (7) together with compression rings (5a, 5b).

3001-0039

Step 2
1. Push stub shaft (7) together with compression rings (5a, 5b)

onto the motor shaft.

2. Check that the clearance between the end of the stub shaft

and the motor flange is 10-20mm (0.39-0.78 inch).

3001-0040

10-20 mm (0.39-0.78 inch)

Step 3
1. Tighten screws (6) lightly and evenly.
2. Ensure that stub shaft (7) can be moved on the motor shaft.

3001-0041

Step 4
1. For a double mechanical shaft seal: Fit drive ring (52) on

stub shaft (7).

2. Fit back plate (25), washers (21) and nuts (20) and tighten.

3001-0042

Step 5
1. Fit impeller (27) on stub shaft (7).
2. Ensure that the clearance between the impeller and back plate

(25) is correct: 0.5mm (0.02 inch) for LKHex-10-60 and 1.0mm
(0.04 inch) for LKHex-70.

3. Tighten screws (6) evenly until the stub shaft (7) cannot move

on the motor shaft.

3001-0043

LKHex 10-60 = 0.5 mm (0.02 inch)
LKHex 70 = 1.0 mm (0.04 inch)

29

 PH: 403.720.0999

Содержание LKHex-10















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды