manualshive.com logo in svg

Alfa Laval LKHex-10, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval LKHex-10 Скачать руководство пользователя страница 26

5 Maintenance

Read the instructions carefully. The items refer to the parts list and service kits section.
Handle scrap correctly.

: Relates to the shaft seal.

Step 5
1. Clean the sealing surfaces with contact cleaner before fitting

back plate (25).

2. Carefully guide the back plate onto adaptor (16).
3. Fit washers (21) and nuts (20).

3001-0034

Step 6
Lubricate O-ring (26) and slide it onto back plate (25).

3001-0035

Step 7
1. Lubricate O-ring (38) and fit it in impeller (37), if impeller screw

is used.

2. Lubricate impeller hub with silicone grease or oil.
3. Screw the impeller onto stub shaft (7).
4. Fit impeller screw (39) and tighten, if used.

Tightening torque for impeller screw:

LKHex 10-60: 20 Nm (15 lbf-ft)
LKHex 70: 50 Nm (37 lbf-ft)

3001-0036

Step 8
Fit safety guards (22) and screw (23) and tighten.
If the pump is not supplied with flush connections, the holes in the
adaptor will be covered by the guard.

3001-0037

Step 9
1. LKHex-10 to -70: Fit pump casing (29), washers (24a) and

screws (24).

2. Adjust the pump casing to the right position.
3. LKH-10 to -70: Tighten nuts (20) for back plate (25) and tighten

cap nuts (24).

Note:
Cap nuts must be tightened according to torque values in the
chapter 6 Technical data

3001-0012

26

 PH: 403.720.0999

Содержание LKHex-10















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды