manualshive.com logo in svg

Alfa Laval LKHex-10, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval LKHex-10 Скачать руководство пользователя страница 27

5 Maintenance

Read the instructions carefully. The items refer to the parts list and service kits section.
Lubricate the rubber seals before fitting them.

: Relates to the shaft seal.

5.4

Assembly of pump/double mechanical shaft seal

Step 1

1. Fit O-rings (15) in rotating seal rings (14).
2. LKH-70: Fit cups (54) on rotating seal rings (14).
3. Fit spring (13) on one of the rotating seal rings (14) and place the drive ring (52) in

between.

Step 2

1. LKH-70: Turn the drive ring (52) in order to place it correctly on the pump shaft (7).
2. Fit the second rotating ring (14) on the other end of the spring.
3. Place the parts on the stationary seal ring fitted in back plate (25).

NOTE
Ensure that both drive pins on the drive ring enter the notches in the rotating seal rings.

Only LKH-70

3000-0098

TD239-007_1

Step 3
1. Lubricate O-ring (44) and slide onto seal housing (40a).
2. Lubricate O-ring (50) and fit on stationary seal ring (51) and fit

this in the seal housing.

3001-0045

Step 4
1. Clean the sealing surfaces with contact cleaner.
2. Fit seal housing (40a) on the back plate (25) and tighten screws

(41).

3001-0046

Step 5
1. To enable fitting of the back plate (25) with the shaft seal,

remove Connex pin (8) from stub shaft (7) (if fitted).

2. Carefully guide the back plate onto adaptor (16).
3. Fit washers (21) and nuts (20).

3001-0034

27

 PH: 403.720.0999

Содержание LKHex-10















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды