manualshive.com logo in svg

Alfa Laval LKH Prime UltraPure, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval LKH Prime UltraPure Скачать руководство пользователя страница 8

3 Installation

Read the instructions carefully and pay special attention to the warnings! Always check the pump before operation.
- See pre-use check in section 3.3 Pre-use check
The pump is heavy.
Alfa Laval therefore recommends the use of a lifting crane when handling the pump.

3.2

Installation

Step 1

Always read the technical data carefully.
(See chaper 6.1 Technical data)

Always use a lifting crane when handling the pump.

Always have the pump electrically connected by authorised
personnel. (See the motor instructions).

CAUTION
Alfa Laval cannot be held responsible for incorrect installation.

WARNING:
Alfa Laval recommends the installation of a lockable repair
breaker. If the repair breaker is to be used as an emergency stop,
the colours of the repair breaker must be red and yellow.

Caution:
The pump does not prevent back flow when
intentionally or unintentionally stopped. If back flow
may cause a hazardous situation to arise, precautions
must be taken e.g. a check valve can be installed in
the system to prevent hazardous situations.

Note:
The 3A standard requires minimum clearance
between the lowest part of the base, pump, motor or
drive and for the floor to be no less than 4 in. (100
mm)

Step 2
Ensure at least 0.5 m (1.6 ft) clearance around the pump.

Step 3
Check that the flow direction is correct.
O: Outlet
I: Inlet

8

Содержание LKH Prime UltraPure

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды