manualshive.com logo in svg

Alfa Laval LKH Prime UltraPure, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval LKH Prime UltraPure Скачать руководство пользователя страница 31

5 Maintenance

Read the instructions carefully. The items refer to the parts list and service kits section.
Lubricate the rubber seals before fitting them.

: Relates to the shaft seal.

Step 10
1. Fit pump casing (29) and washers (24a). Fit and tighten cap

nuts (24). Torque = 20Nm/15 lbf-ft

2. Adjust pump casing (29) to correct position
3. Tighten nuts (20) for back plate (25), according to torque values

in chapter 6, Technical data

4. Fit air screw (58) and tighten with a spanner (Torque = 20Nm

(15 lbf-ft))

Step 11
1. Fit front cover O-ring (59) and fit and align front cover (60)
2. Fit clamp and tighten screws (57) gently
3. Fit recirculations pipe (56), align front cover (60) and tighten

unions

4. Tighten clamp screws (57)

Step 12
Fit safety guard (22) and screw (23), then tighten.
If pump is not supplied with flush connections, the holes in the
adapter will be covered by the guard.

31

Содержание LKH Prime UltraPure

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды