Alfa Laval LKH Prime UltraPure Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 48

Alfa Laval LKH Prime UltraPure Скачать руководство пользователя страница 19

5 Maintenance

Maintain the pump with care. Read the instructions carefully and pay special attention to the warnings!
Always have spare shaft seals and rubber seals to hand.
See separate motor instructions.
Check the pump for smooth operation after service.

5.1

General maintemance

Step 1

!

Always read the technical data carefully. (See section 6.1)

Always disconnect the power supply when servicing the pump.

NOTE
All scrap must be stored//disposed of in accordance with current regulations/directives.

Step 2

!

Never service the pump when it is hot.

Risk of burns!

Step 3

!

Never service the pump if pressurised.

CAUTION
Fit the electrical connections correctly if they have been removed
from the motor during service.

CAUTION
Pay special attention to the warnings!

Atmospheric
pressure
required!

Step 4
Recommended spare parts:
Order service kits from the service kits list
(See section 7).

Ordering spare parts
Contact your local Alfa Laval sales company.

19

«
...
17
18
19
20
21
...
»

Содержание LKH Prime UltraPure

















































Отзывы:

Нет отзывов