Alfa Laval LKH Prime UltraPure Скачать руководство пользователя страница 29

Страница: 29 / 48

5 Maintenance

Read the instructions carefully. The items refer to the parts list and service kits section.
Lubricate the rubber seals before fitting them.

: Relates to the shaft seal.

5.5

Assembly of pump/double mecanical shaft seal

Step 1

1. Fit O-rings (15) in rotating seal rings (14)
2. Fit spring (13) onto one of the rotating seal rings (14) and place the drive ring (52) in between

Step 2
1. Fit the second rotating ring (14) on the other end of the spring
2. Place the parts on the stationary seal ring fitted in the back

plate (25)

NOTE
Ensure that both drive pins on the drive ring are inserted into the
notches in the rotating seal rings.

Step 3
1. Lubricate O-ring (44) and slide onto seal housing (40a)
2. Lubricate O-ring (50) and fit on stationary seal ring (51), then fit

this in the seal housing

Step 4
1. Fit O-ring (12) on stationary seal ring (11) and lubricate
2. Screw the stationary seal ring into the back plate (25)

CAUTION
Only tighten by hand to avoid deforming the stationary seal ring.
(Max. 7 Nm/5 lbf-ft)

Use
the tool
supplied

Left-hand
thread!

*) NOTE! : If fitting SiC/SiC single seal, the
static seal face must be marked “LKH Prime”.

Содержание LKH Prime UltraPure

















































Результаты поиска

Содержание LKH Prime UltraPure

Отзывы:

Похожие инструкции для LKH Prime UltraPure

Бренды по названию

Популярные бренды

Alfa Laval LKH Prime UltraPure, Инструкция по эксплуатации

Результаты поиска

Содержание LKH Prime UltraPure

Отзывы:

Похожие инструкции для LKH Prime UltraPure

Бренды по названию

Популярные бренды