background image

1.SAFETY PRECAUTIONS 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

1

–1

 

Always read the MAINTENANCE 

– 

OPER

ATION AND USER’S MANUAL carefully 

before operating the generator set. The 
generator set that you have purchased may 
operate safely and reach its performance 
when the proper operating conditions 
specified in the manufacturer’s instructions 
are provided; the generator set is operated 
and maintained under these conditions. 

 

 
GENERAL DECLARATION 

 

It is the responsibility of 
purchaser/installer/owner of the generator 
set to provide conformity of the machine 
with the relevant legislation and 
instructions, to take all health and safety 
precautions, and to protect the generator set 
before commissioning the generator set. 

 
Following cautionary symbols and inscriptions 
are used in this manual to warn and protect the 
users of the generator and service personnel 
against potential dangers of the generator set. 
Please read carefully until the end of the 
manual.

 

 

 : This warning describes dangers 

that may cause serious personal injuries or 
death. 
 

 : This warning describes dangers 

that may cause serious personal injuries or 
death or against operating conditions that is 
required in safety precautions. 
 

 : This warning describes dangers 

that may cause serious personal injuries or 
equipment damages or against operating 
conditions that is required in safety 
precautions. 
 
ENGINE EXHAUST IS LETHAL 

 

Never sleep inside of the vessel while the 
generator has been operating unless your 
vessel is equipped with proper carbon monoxide 
detectors.  
Generator Exhaust kit (exhaust muffler, exhaust 
gas-sea water separator, exhaust hose, clamps) 
shall be installed according to the 
manufacturer’s instructions by authorized 
personnel. 
Check for exhaust gas leaks in the first 
operation or every eight hours of operation. 
All passengers and personnel shall be moved to 
open air areas of the vessel when a gas leak is 
detected, and an ambulance shall be called 
when it is necessary. Operate the generator set 
after the repair of the exhaust gas leak.

 

GENERATOR VOLTAGE IS LETHAL 

All power, control cables and connecting 
elements that will be connected externally to the 
generator shall be connected by a trained and 
experienced technician according to the current 
legislation and manufacturer’s instructions. 

 

The power generator current and main coastal 
(dock) power current mustn’t and prevented short 
circuit when both using at the same time. It may 
cause danger. Feedback to main coastal (dock) 
supply may cause damage on the vessel 
equipment and electric shocks that may result as 
serious personal injuries or death.

 

Always be careful when intervening on any 
electrical equipment of the generator set. Take off 
any jewelry; ensure that your clothes and shoes 
are dry. Stand on a wooden or rubber platform 
and use insulated electric repair tools during your 
work.

 

 
DIESEL FUEL IS FLAMMABLE 

Do not turn the electrical switches on/off and 
smoke in inadequately ventilated areas where 
fuel vapors may be available. Keep far away any 
equipment that generate flames, sparks and arcs 
and all other flammable sources from these 
areas.

 

 
MOVING PARTS MAY CAUSE SERIOUS 
INJURIES OR DEATH 

Do not wear loose clothes and take off your 
jewelry if you need to work near moving parts. 
Wear the clothes that are suitable for the 
operating conditions if possible. Keep away from 
all moving parts (fan, belt, pulley etc.) in your 
work.

 

 
BATTERY GAS IS EXPLOSIVE 

Always wear safety goggles while working on the 
batteries. Battery acid has extreme corrosive 
effect so be very careful. Do not smoke while you 
are working. Keep far away any equipment that 
generate flames, sparks and arcs and all other 
flammable sources from these areas.

 

Always disconnect the negative (-) battery cable 
at first, and re-connect the negative (-) battery 
cable most recently for reducing any arcs while 
you are opening connections of the battery 
cables.

 

Содержание MG 309












































Отзывы: