Albatron K8NF4X-754 Скачать руководство пользователя страница 16

Страница: 16 / 54

Mainboard K8NF4X–754

Reset Switch Header

(Blue)

: RST_SW

This header can be attached with a momentary SPST button cord. The switch is normally left

open. When the switch closed, it will cause the mainboard to reset and run the POST
(Power-On Self Test).

Power-on Switch Header

(Orange)

: PWR_SW

This header can be attached with a PC front panel power switch cord. The power switch cord

must pull the power switch pin to ground for at least 50 ms to signal the power supply to turn

on or off (the time required is due to internal debounce circuitry on the system board). At

least two seconds must pass before the power supply will recognize another on/off signal.

Power LED Header

(Green)

: PWR_LED

Attach the power LED cord onto this header, then the power LED will illuminate while the

system is powered on.

Speaker Header

(Purple)

: SPEAKER

A PC front panel speaker cord can attach onto this header. When you reboot the system, the

speaker will sound a short “beep”. If there is something wrong during the Power On Self-Test,
the speaker otherwise will sound “irregular beep” to let you know.

Headers & Jumpers

Front USB Headers: USB1/2

There are four USB 1.1/2.0 ports have provided on this mainboard, and it also provides two

front USB headers which allowing you to set four additional USB ports on your PC front

panel. An optional USB bracket may be included within this product and you can attach more

USB devices on it.

Pin

Assignment

Pin

Assignment

1 +5V

(fused)

2 +5V

(fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

USB1/USB2

9 Key

N/A

Pin

Assignment

Pin

Assignment

1 PC_BEEP 2 N/C

SPEAKER

3 Ground

4 +5V

Attention

If you are using a USB 2.0 device with Windows 2000/XP, you will

need to install the USB 2.0 driver from the Microsoft

website. If you

are using Service pack 1 (or later) for Windows

XP, and using

Service pack4 (or later) for Windows® 2000, you will not have to

install the driver.

Содержание K8NF4X-754























































Результаты поиска

Содержание K8NF4X-754

Отзывы:

Похожие инструкции для K8NF4X-754

Бренды по названию

Популярные бренды

Albatron K8NF4X-754, Руководство пользователя

Результаты поиска

Содержание K8NF4X-754

Отзывы:

Похожие инструкции для K8NF4X-754

Бренды по названию

Популярные бренды