Albatron K8NF4X-754 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 54

background image

Mainboard K8NF4X–754

26

IDE Prefetch Mode

The “onboard” IDE drive interfaces supports IDE prefetching for faster drive access. If you
install a primary and/or secondary add-in IDE interface, set this option to “Disabled” if the

interface does not support prefetching. Options: Enabled (default), Disabled.

IDE HDD Block Mode

Block mode is otherwise known as block transfer, multiple commands, or multiple sector

read/write. Select the “Enabled” option if your IDE hard drive supports block mode (most new

drives do). The system will automatically determine the optimal number of blocks to read
and write per sector. Options: Enabled (default), Disabled.

RAID Config

If you highlight the “RAID Config” label and then press the enter key, it will take you to a
submenu with the following options:

SATA1/2 Primary/ Secondary RAID

This allows you to enable or disable the RAID function for the SATA1 /2/Primary/ Secondary

device. Options: Enabled, Disabled(default).

Serial-ATA 1/2

This item allows you to enable or disable the SATA1/2 device. Options: Enabled (default),

Disabled.

SATA Spread Spectrum

When you installed a SATA device this item will allow you to enable/ disable the SATA speed
spread spectrum. We recommend you to enabled this item to decrease EMI noise.
Options: Enabled (default), Disabled.

Onboard Device

If you highlight the “Onboard Device” label and then press the enter key, it will take you to a
submenu with the following options:

OnChip USB

This option should be enabled if your system has a USB port installed on the system board.
You will need to disable this feature if you add a higher performance controller.
Options: V1.1+V2.0 (default), Disabled, V1.1.

USB Memory Type

This item allows you to set your USB Memory Type.
Options: SHADOW, Bast Memory(640k)(default).

USB Keyboard Support

This item allows you to enable the USB attached keyboards and storages.

Options: Disabled (default), Enabled.

«
...
28
29
30
31
32
...
»

Содержание K8NF4X-754























































Отзывы:

Нет отзывов

Похожие инструкции для K8NF4X-754

Бренд: IEI Technology Страницы: 211

Бренд: IEI Technology Страницы: 8

Бренд: IEI Technology Страницы: 8

Бренд: IEI Technology Страницы: 177

Бренд: JETWAY Страницы: 56

Бренд: Zotac Страницы: 56

Бренд: Gigabyte Страницы: 96

Бренд: National Semiconductor Страницы: 22

Бренд: AOpen Страницы: 8

Бренд: Zeal-All Страницы: 9

Бренд: ETOP Страницы: 68

Бренд: ASROCK Страницы: 65

MOTORKIT-91F267-MC

Бренд: Fujitsu Страницы: 33

Бренд: Fujitsu Страницы: 30

Бренд: Fujitsu Страницы: 16

Бренд: Fujitsu Страницы: 14

Бренд: Fujitsu Страницы: 24

Бренд: Fujitsu Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды