Albatron K8NF4X-754 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 54

background image

Mainboard K8NF4X–754

20

Advanced BIOS Features

Removable Device Priority

Select removable device boot priority.

Hard Disk Boot Priority

Select hard disk drive boot priority.

First /Second/Third Boot Device

Select the order in which devices will be searched in order to find a boot device.
Options: Removable (default for first boot device), CD ROM (default for second boot device),

Hard Disk (default for third boot device), Disabled.

Boot Other Device

Set to “Enabled” allows the system trying to boot from other devices if the system fails to
boot from the 1st/ 2nd/ 3rd boot devices. Options: Enabled (default), Disabled.

Boot Up Floppy Seek

When Enabled, the BIOS tests (seeks) floppy drives to determine whether they have 40 or

80 tracks. Only 360-KB floppy drives have 40 tracks. Drives with 720KB, 1.2MB, and 1.44MB

capacity all have 80 tracks. Because very few modern PCs have 40-track floppy drives, we

recommend that you set this field to “Disabled”.
Options: Enabled, Disabled (default).

«
...
22
23
24
25
26
...
»

Содержание K8NF4X-754























































Отзывы:

Нет отзывов

Похожие инструкции для K8NF4X-754

Бренд: IBASE Technology Страницы: 33

Бренд: Gigabyte Страницы: 96

Бренд: PRIZM Страницы: 9

STEVAL-PLC001V1

Бренд: ST Страницы: 42

Бренд: Bartels Mikrotechnik Страницы: 9

Blood-Iron P45 Elite Series

Бренд: LanParty Страницы: 134

Бренд: Supermicro Страницы: 109

Бренд: Ublox Страницы: 2

Бренд: MSI Страницы: 87

Бренд: NXP Semiconductors Страницы: 4

Бренд: Gigabyte Страницы: 44

Бренд: Norco Страницы: 55

Бренд: Lantronix Страницы: 20

Memorator Pro 2xHS v2 CB

Бренд: Kvaser Страницы: 22

Бренд: EPOX Страницы: 83

Бренд: ASROCK Страницы: 139

Бренд: Asus Страницы: 2

EX-H310M-V3 R2.0

Бренд: Asus Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды