Alarm Lock Trilogy DL2800, Инструкция по программированию

Страница: 32 / 36

32
ACCESS = Entry into a restricted area.
AUDIT TRAIL = A date/time stamped log of previous lock events.
BURGLARY CONTROL PANEL = Provides local alarm and remote
communication to request security for burglary/break-in.
CLOCK
•
REAL TIME CLOCK = An accurate built-in clock that allows date/
time stamping of events. The clock can be slowed or speeded up
to fine tune long term accuracy to within three minutes per year.
•
CLOCK SETTINGS = Printout includes date, time, weekday, and
clock speed.
•
CLOCK SPEED = The clock can be adjusted to allow faster/slower
speeds and therefore increasing clock accuracy.
CODE
= Numeric sequence of numbers (such as: 1234) entered at the
keypad. If Star-Enter-Key is required, must be followed by a [
:
]
key.
•
BASIC USER CODE = User Codes assigned to User Numbers
12+ (except Users 299-300). (Basic User Codes do not allow pro-
gramming)
•
INVALID CODE = A User Code that has not been programmed in
the lock.
•
MANAGER CODE = User Codes assigned to User Numbers 2
through 6. (Allows most programming functions).
•
MASTER CODE = The User Code assigned to User Number 1.
The Default (factory) Master Code is 123456. The User with the
Master Code has complete control of the lock (no programming
restrictions).
•
SERVICE CODE = User 300 User Code. Allows only one use,
then must be re-enabled by Function 9.
•
SUPERVISOR CODE = User Codes assigned to Users 7 through
11. Can only program certain day-to-day operational functions.
•
USER CODE = Code used by Users. A User Code is 3 to 6 nu-
meric digits long, pressed into the keypad buttons, allowing con-
trolled entry by Users.
•
VALID CODE = An entered User Code that has been programmed
in the Lock Program.
COM PORT
= A computer serial communications port used to commu-
nicate with the Lock and/or Data Transfer Module.
DATA TRANSFER MODULE = A device that permits transfer of pro-
gram/data between a computer and the lock.
DATE = Month, Day and Year entered as MMDDYY.
DAY OF WEEK
= Sunday through Saturday (where 1 = Sunday and 7
= Saturday).
DEFAULT = Default settings are the original settings that were set at
the factory; in other words, it is the lock's original factory condition
when the lock was first taken out of its original box. The default
settings are permanently encoded within the lock's fixed memory,
and when the lock is first started, or when power is removed and
re-applied (see Wiring, Power-Up & Battery Replacement, page
10), the original factory default settings are re-loaded and take ef-
fect.
DISABLE = Turn off.
DOOR NUMBER = Identification of each door lock with a specific num-
ber in order to ensure that the correct lock is associated with the
correct lock programming within DL-Windows or the AL-DTM.
Note: "Door Number" is a term used with AL-DTM versions 1 and
2 and with DL-Windows versions 3.5.0 and earlier. Later versions
of the AL-DTM and DL-Windows monitor door numbers automati-
cally, therefore there is no need to manually change door numbers
via the keypad. Therefore, Function 59 is no longer used with the
later versions of the AL-DTM and DL-Windows.
DOWNLOAD = To receive data from the lock into the AL-DTM or DL-
Windows.
ENABLE = Turn on.
EVENTS
= Recorded lock activity.
FUNCTION
(also called Programming Functions ) = are the numbers
used to program lock features (enabling/disabling Users, User
Groups, Passage Mode, Schedules, etc.).
GROUP
•
USER GROUP = Defining a User to specific Groups, allows
User entry when the Group is allowed entry.
•
GROUP 1 ENABLES GROUP 4 USERS = A Group 1 USER
CODE entry during a predefined schedule will allow access to
Group 4 Users. See page 26.
•
GROUP 1 PUTS UNIT IN PASSAGE = A Group 1 USER CODE
entry during a pre-defined schedule will unlock unit. See page
25.
INSTALLER = See.... CODE, INSTALLER CODE.
KEYPAD = 10-numeric keys,
:
and special
;
key.
•
KEYPAD LOCKOUT = Keypad is programmed to lockout Us-
ers, for a specified period of time, when a specified number of
invalid User Codes are entered.
•
KEYPAD PROGRAMMING = Ability to program the lock
through the keypad.
KEYPRESS = Pressing a button on the lock’s keypad.
LEVEL ABILITY = Predefined User Types (such as Master, Manager
and Supervisor) each having specific abilities to program and/or
control the lock.
Glossary